EEWORLDEEWORLDEEWORLD

Part Number

Search

8425MH9W4BE

Description
PUSHBUTTON SWITCH,STRAIGHT,4PDT,ON-(ON),WP STRAIGHT TERMINAL,12
CategoryMechanical and electronic products    switch   
File Size1017KB,16 Pages
ManufacturerC&K Components
Download Datasheet Parametric View All

8425MH9W4BE Overview

PUSHBUTTON SWITCH,STRAIGHT,4PDT,ON-(ON),WP STRAIGHT TERMINAL,12

8425MH9W4BE Parametric

Parameter NameAttribute value
Objectid1166019276
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator angle
Actuator length0.267 inch
Actuator materialGLASS FILLED NYLON
Actuator typePUSHBUTTON
body width21.59 mm
body height52.1716 mm
Body length or diameter12.7 mm
Casing diameter0.25 inch
Nozzle length0.25 inch
Casing typeUNTHREADED
Center contact platingGOLD OVER NICKEL
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact functionON-(ON)
Contact resistance0.05 mΩ
Dielectric withstand voltage1000VAC V
Electrical life60000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Manufacturer's serial number8020
Installation featuresTHROUGH HOLE-STRAIGHT
Maximum operating temperature75 °C
Minimum operating temperature-30 °C
PCB hole count12
sealEPOXY
SolderabilityMIL-STD
surface mountNO
Switch actionVERTICAL
switch function4PDT
Switch typePUSHBUTTON SWITCH
Terminal length1.062 inch
Terminal materialCOPPER ALLOY
Termination typeWIRE WRAP
WashabilityPARTIAL
Printed from www.freetradezone.com, a service of Partminer, Inc.
This Material Copyrighted By Its Respective Manufacturer
msp430f5529 I2C help
I use P3.5 and P3.6 to simulate the I2C bus, but I can't get the correct waveform. Can you guys give me some advice? The program and waveform are as follows: void IICstart() { P3OUT|=BIT5;//First make...
hxm3213 Microcontroller MCU
I want to make an installation file. What tool should I use to make it? Can InstallShield be used to make an installation disk on WinCE? (Run on PC and install on WinCE)
I want to make an installation file. What tool should I use to make it? Can InstallShield be used to make an installation disk on WinCE? (Run on PC and install on WinCE)...
seewei Embedded System
Remote LED brightness adjustment software development based on STM32 embedded microcontroller development board
I. Embedded Software Programming (100 points) According to the following requirements, complete the embedded software development task of the project in a group and achieve the expected functions. l P...
太自负了 stm32/stm8
Wav audio compression problem under WinCE
The device has a recording function, but the WAV file is PCM data, which is too large. I want to compress it. Does anyone have any good ideas? I compressed PCM into ADPCM, but the effect is not good a...
yousijia Embedded System
How to choose a power supply for automotive camera modules
As automotive camera technology evolves to higher resolutions, dynamic ranges, and frame rates, power architectures need to be tailored to the specific use case requirements. In this article, I will r...
alan000345 Analogue and Mixed Signal
Can anyone provide a C51 program for timer T2 to count down?
I am now using the down counting program of timer T2, RCAP2H=0x0B; RCAP2L=0xDC; how to initialize the system and how to input the pulse from the T2 pin to achieve down counting....
xinxi Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2526  2565  1953  1281  77  51  52  40  26  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号