EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8A-03-2700-G-D

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 270ohm, 2% +/-Tol, -25,25ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GL8A-03-2700-G-D Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 270ohm, 2% +/-Tol, -25,25ppm/Cel, 4430,

GUB-GL8A-03-2700-G-D Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid795553495
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.2
structureMolded
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.16 W
resistance270 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Tolerance2%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Introduction to TI battery failure modes and BMS related solutions
First, let’s take a look at the battery failure modes. Why do batteries fail? 1. Battery aging – internal resistance and capacity[align=center][/align] [align=left] 2. Battery cell related issues[/ali...
alan000345 Analogue and Mixed Signal
ucGUI problem help (12 DROPDOWN controls defined cannot be displayed)
/* ****************************************************************** **uCGUIBuilder** **Version:4.0.0.0** **2012 / 04** **CpoyRight to: wyl** **Email:ucguibuilder@163.com** **This text was Created by...
shkhlove Real-time operating system RTOS
I played with the 3D printer sent by cardin6 for two days.
[i=s]This post was last edited by wugx on 2016-10-7 21:02[/i] A batch of printer parts arrived from July to October. I installed them these two days and found that the design of this printer is simple...
wugx MicroPython Open Source section
Two small circuit design mistakes
[p=24, null, left][color=rgb(73, 73, 73)][font=微软雅黑]Today I will write about two circuit design errors. The first one is caused by insufficient current gain. This circuit is based on the design of oth...
eeskill Analog electronics
485 communication encountered strange problems!
When I was doing 485 communication between PC and 51 MCU, I used three wires to connect, A, B and GND, and used 232-485 converter on PC side, and ran Serial Port Wizard. During communication, MCU firs...
longxin Embedded System
2008 Transcript - Review
Things to pay attention to in the development of power amplifier products: electromagnetic compatibilityStrong current loops and weak currents cannot be grounded. Try to use a single point grounding. ...
btty038 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2195  2513  2252  2874  301  45  51  46  58  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号