WBDDSS8-A-01-6650-B-G datasheet, PDF

WBDDSS8-A-01-6650-B-G: DescriptionArray/Network Resistor, Isolated, 0.1W, 665ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 1408,; CategoryPassive components The resistor; File Size273KB，4 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

WBDDSS8-A-01-6650-B-G Overview

Array/Network Resistor, Isolated, 0.1W, 665ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 1408,

Parameter Name	Attribute value
Objectid	819393921
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Isolated
Number of terminals	16
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	0.406 mm
Package length	3.556 mm
Package form	SMT
Package width	2.032 mm
method of packing	Tray
Rated power dissipation(P)	0.1 W
resistance	665 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC-NETWORK
size code	1408
Temperature Coefficient	100 ppm/°C
Tolerance	0.1%
Operating Voltage	100 V

Wire Bondable

Resistor Network Arrays

Chip Network Array Series

Absolute tolerances to ±0.1%

Tight TCR tracking to ±5ppm/°C

Ratio match tolerances to ±0.05%

Ultra-stable tantalum nitride resistors

IRC’s TaNSil

network array resistors are ideally suited for applications that demand a small footprint. The small wire

bondable chip package provides higher component density, lower resistor cost and high reliability.

The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking and low cost.

Excellent performance in harsh, humid environments is a trademark of IRC’s self-passivating TaNSil

resistor film.

For applications requiring high performance resistor networks in a low cost, wire bondable package, specify IRC

network array die.





General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

10. 11

I am a high frequency person, I would like to recommend a high frequency group, welcome to join the discussion: [i=s]This post was last edited by paulhyde on 2014-9-15 09:06[/i] 89789552...; 鉴主13楼 Electronics Design Contest

How to configure registers for audio sampling chip using stm32f411 microcontroller: I am an FPGA developer. However, when using FPGA to configure the audio sampling chip tlv32, I need to use stm32f411 to configure the sampling chip using the i2c bus protocol. I don't know how to conf...; whllieying stm32/stm8

Wireless camera components: Keywords: Wireless camera consists of two parts: video circuit and audio circuit. The video part mainly consists of optical system, camera device, preamplifier, synchronous scanning system, control sy...; gzycxfj Industrial Control Electronics

Matlab 7.0: Excuse me, where can I download matlab 7.0...; koksvalue Embedded System

LPC2114 MDK startup problem: I used KEIL350 to create an LPC2114 MCU project. However, after creating the project and creating the main function, I found that the program did not run to the main function. However, when I burned t...; hsywgf Embedded System

Calculate engine speed using the charging signal from the battery on a diesel engine: The engine speed is 1500 rpm, the AD sampling rate is 70K, and a total of 1024 points are collected. The time domain waveform is as follows:The red circle is the interference waveform, which has a lar...; Universe12 Integrated technical exchanges

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components