EEWORLDEEWORLDEEWORLD

Part Number

Search

LG400M0270BP443535

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 400V, 20% +Tol, 20% -Tol, 270uF,
CategoryPassive components    capacitor   
File Size209KB,8 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

LG400M0270BP443535 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 400V, 20% +Tol, 20% -Tol, 270uF,

LG400M0270BP443535 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid746285530
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance270 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter35 mm
dielectric materialsALUMINUM (WET)
length35 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package formSnap-in
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)400 V
ripple current1200 mA
YAGEO CORPORATION
ELECTROLYTIC CAPACITORS
Large Can Aluminum
Electrolytic Capacitors
LG
[ For General ]
For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply
Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
6.3 to 100VDC
560 ~ 82000µF
±20% at 120Hz, 20°C
I = 0.02CV, L = 20m/m, I = 0.03CV or 3mA whichever is smaller.
(After 5 Minutes Application of DC Working Voltage at 20°C)
I = Leakage Current (µA), C = Nominal Capacitance (µF),V = Rated Voltage (V)
Dissipation Factor (tanδ)
Rate Voltage (V)
D.F. (%)
Low Temperature Stability
Impedance Ratio (Max.)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
6.3~100V
160~250V
315~450V
50
60
120 1K
10K
Endurance
0.88 0.90 1.00 1.15 1.16
0.85 0.88 1.00 1.15 1.20
0.88 0.90 1.00 1.10 1.15
6.3
60
10
55
16
55
25
45
35
35
50
30
63-100 160-400 450
25
15
20
-25 to +105°C
160 to 450VDC
47 ~ 2200µF
DESCRIPTION
Endurance : 105°C 2000 hours, higher temperature
than LH.
Ideally suitable for using in switching power supplies
and other industrial / commercial applications.
Measurement frequency: 120Hz
Rated Voltage (V)
Z(-25°C) / Z(20°C)
Z(-40°C) / Z(20°C)
6.3~16 25
4
15
3
10
35
3
8
50~63
2
6
80~10 160~400 450
2
5
4
-
8
-
After the rated voltage and rated ripple current have been applied at 105°C
for 2000 hours, the capacitors shall meet the following requirements.
(a)
Capacitance Change:
±20% of the Initial Value
(b)
Dissipation Factor:
200% of the Initial Specified Value
(c) Leakage Current:
the Initial Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Location of P.C.B. Holes
Vinyl Sleeve
0.9
±
0.1
10
±
0.5
2mm x 2
3.0
0.8+0.2 /-0.1
Botton Plate
Negative
Unit: mm
10
±
0.5
5.8
±
1.0
1.5+0.2 /-0.1
Safety Device
L+2 Max.
5.8
±
0.1
D
±
1
MSP430 clock interrupt enters abnormality
[backcolor=white]The following code function P1.0 outputs ACLK clock, P2.0 is used as capture pin, captures the signal of P1.0, and is triggered by the rising edge. In the capture interrupt, character...
kui Microcontroller MCU
I have finished the serial port driver, and will start working on the SD card driver tomorrow. Can you provide me with some information?
As the title says, it took me two weeks to finally get the serial port driver working. Now my serial port 1 and serial port 2 can send and receive data from the outside world normally. Tomorrow I will...
happyboy22 Embedded System
Is smart home far away from us?
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i]   Nowadays, it is common for families to have multiple TVs. What should family members do if they want to watch digital pay TV i...
songbo Mobile and portable
Why do we need to enable the JTAG pull-up resistor in the 8962 can_device_qs routine?
Why do we need to enable the JTAG pull-up resistor in the 8962 can_device_qs routine?// // Enable the pull-ups on the JTAG signals. // SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC); GPIOPadConfigSet(GPI...
academic Microcontroller MCU
A new round of group buying will start next week!
Attention all forum users , we will organize a group purchase of TI development boards next week !This group purchase requires that you post no less than 3 technical posts in the TI community !Before ...
maylove Microcontroller MCU
STM32 RTC clock
I am debugging the RTC peripheral of STM32F103ZET today. I have written similar programs before. When debugging today, the RTC cannot be initialized. I will paste the initialization code as follows: v...
asd046012 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2559  753  73  2765  1196  52  16  2  56  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号