EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S271AG-0015CD

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size729KB,17 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance  
Download Datasheet Parametric View All

8N4S271AG-0015CD Overview

LVDS Output Clock Oscillator

8N4S271AG-0015CD Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1327869213
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TRAY
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
JESD-609 codee3
Installation featuresSURFACE MOUNT
Nominal operating frequency156.25 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
Terminal surfaceMatte Tin (Sn)
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S271
DATA SHEET
General Description
The IDT8N4S271 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Q
nQ
Pin Assignment
OSC
f
XTAL
2
÷P
÷N
DNU 1
OE 2
GND 3
6 V
DD
5 nQ
4 Q
÷MINT,
MFRAC
IDT8N4S271
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
25
Configuration Register (ROM)
OE
Pullup
7
IDT8N4S271CCD
JUNE 12, 2012
1
©2012 Integrated Device Technology, Inc.
Does the Linux 2.6.14 kernel support the Yaffs2 file system?
As the title says? Do I need to patch this kernel with yaffs2? Does anyone have the yaffs2 source code to share? Also, which kernel can support yaffs2 without patching?...
wonderglass Linux and Android
Power supply design solutions in medical equipment
[i=s]This post was last edited by qwqwqw2088 on 2014-4-9 08:27[/i] [p=24, 2, left][color=rgb(62, 62, 62)][font=Tahoma, Arial, sans-serif]Transfer[/font][/color][/p][p=24, 2, left][color=rgb(62, 62, 62...
qwqwqw2088 Analogue and Mixed Signal
MOSFET turn-on schedule question
As shown in the figure, Pspice simulates the mosfet turn-on process. The waveform obtained by simulation is shown in the figure (blue is Vds, red is Vgs, and green is Id), which is different from the ...
ujs Analog electronics
About 1602 display problem
Give me the code first, [code]CW DATA 0F9FCH ;write instruction CR DATA 0F9FEH ;read status DIW DATA 0F9FDH ;write data DIR DATA 0F9FFH ;read data ORG 0000H AJMP START ORG 0030H PANYAO: DB 'C51',0 STA...
xyw Embedded System
Air pressure and altitude conversion display
I made a barometric altimeter. The display of barometric pressure has been solved, but the height has not been solved. How can I change the conversion relationship between barometric pressure and heig...
zh7031907 MCU
mega16, I don't know how to write the program to set the upper and lower temperature limits
There is no problem with 1602 LCD display and DS18B20 temperature measurement, but I want to set upper and lower limit alarms. I would like you to teach me or help me write it. Thank you very much. Wr...
Hsmallguy Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2860  871  2234  975  2616  58  18  45  20  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号