D-300-08CS1108 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wire/cable> D-300-08CS1108

D-300-08CS1108: Descriptionsolder & shield tubing splice Encap. cap 2.03-3.04 dia; CategoryWire/cable; File Size68KB，7 Pages; ManufacturerAll Sensors; Environmental Compliance

Download Datasheet Parametric Compare View All

D-300-08CS1108 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	D-300-08CS1108	-	-	View	Buy Now

D-300-08CS1108 Overview

solder & shield tubing splice Encap. cap 2.03-3.04 dia

D-300-08CS1108 Parametric

Parameter Name	Attribute value
Manufacture	TE Connectivity
Product Category	Solder & Shield Tubing
RoHS	Yes
Type	Splice Caps
Factory Pack Quantity	1000

Preview

Download Datasheet

View All

CUSTOMER DRAWING

3mm

±1mm

Product Dimensions

As Received

After Free Recovery

A±2.54

(A±0.100)

25.40

(1.000)

27.90

(1.100)

33.02

(1.300)

øB

min

4.32

(0.170)

6.35

(0.250)

9.14

(0.360)

min

0.30

(0.012)

0.38

(0.015)

0.38

(0.015)

øB

max

2.03

(0.080)

3.05

(0.120)

4.57

(0.180)

min

0.76

(0.030)

1.02

(0.040)

1.27

(0.050)

Product

Name

D-300-08

D-300-12

D-300-18

Maximum

Weight

Pounds/mpc

1.15

2.55

4.50

MATERIALS

1. MOLDED CAP: Heat-shrinkable, cross-linked modified polyolefin.

2. MELTABLE RING: Modified thermoplastic.

3. DEFORMABLE DAM: Radiation cross-linked, thermally stabilized modified polyolefin.

APPLICATION

1. These parts are designed to meet the requirements as shown in the Requirements Section when tested as listed.

2. Parts to be assembled as outlined herein.

3. “B” recovered is the maximum inside diameter of the heat-shrinkable cap.

4. “W” is the wall thickness of the molded cap only, and is measured along the vertical wall.

5. “A” is the average length of the cap and is equal to (A min + A max)/2.

1.0

SCOPE

This document covers the requirements and test procedures applicable to heat shrinkable, stub-splice

encapsulation cap (caps) and the molded component thereof.

2.0

APPLICABLE DOCUMENTS

The specifications and standards referenced herein shall form part of this specification to the extent

specified.

Tyco Electronics

305 Constitution Dr

Menlo Park, CA

94025, U.S.A.

TITLE:

CAP, SPLICE ENCAPSULATION

DOCUMENT NO.:

Unless otherwise specified dimensions are in millimeters.

[Inches dimensions are shown in brackets]

TOLERANCES:

0.00 N/A

0.0 N/A

0 N/A

DRAWN BY:

ANGLES: N/A

ROUGHNESS

IN MICRON

CAGE CODE:

Raychem

Devices

D-300-08/-12/-18

REV:

DATE:

Tyco Electronics reserves the right to

amend this drawing at any time. Users

should evaluate the suitability of the

product for their application.

ECO NUMBER:

REPLACES:

SCALE:

SIZE:

31-July-08

SHEET:

M. FORONDA

06090

D010044

08-018889

NTS

1 of 7

If this document is printed it becomes uncontrolled. Check for the latest revision.

CUSTOMER DRAWING

3.0

3.1

REQUIREMENTS

Material: The splice encapsulation caps shall be fabricated from the materials specified on sheet 1 of this

specification. The materials shall be homogenous and essentially free from flaws, defects, pinholes, seams,

cracks and inclusions.

Color: The caps shall be black.

Properties of Molded Component: The molded component and the material from which it is fabricated

shall meet the requirements in Table 1.

Properties of Finished Caps: The finished caps shall meet the requirements of Table 2.

QUALITY ASSURANCE PROVISIONS

3.1.1

3.1.2

3.1.3

4.0

4.1

4.1.1

4.1.2

Classification of Tests:

Qualification of Tests: Qualification testing shall consist of all test listed in this specification.

Acceptance tests: Acceptance tests shall consist of those tests applicable to Test Groups A and F of

Table 2.

4.2

Sampling Instructions:

4.2.1

Qualification Test Samples: Qualification testing shall consist of six molded slabs, 6 x 6 x 0.075± .010

inches and 62 D-300-12 caps. The molded slabs shall be fabricated from the same lot of material and shall

be subjected to the same degree of cross-linking as the molded components.

4.2.2

Acceptance Test Samples: Acceptance test samples shall consist of finished caps selected at random in

accordance with ANSI/ASQC Z1.4, Inspection Level S-2, AQL 6.5%. A lot of finished caps shall consist

of all caps fabricated from the same lot of molded components, from the same production run, and offered

for inspection at the same time.

4.3

Test Procedures – Molded Slabs

4.3.1

Tensile Strength And Ultimate Elongation: Three specimens cut from a molded slab, using die D of

ASTM D 412, shall be tested for tensile strength and ultimate elongation in accordance with ASTM D 412.

4.3.2

Low-Temperature Flexibility: A 6- x ¼ inch specimen cut from a molded slab shall be mounted in a loop

position between movable, parallel, sets of jaws 2 ½ inches apart, mounted on a test fixture. Each end of

the specimen shall extend at least ¾ inch into a set of jaws and shall be firmly fastened. The specimen and

the test fixture shall be conditioned for four hours at –55 ± 2°C (-67 ± 4°F). While at this temperature, the

sets of jaws shall be moved rapidly from a 2 ½ inch to a 1 inch separation.

4.3.3

Heat Shock: Three 6 x ¼ inch specimens, cut from a molded slab, shall be conditioned for four hours in a

225 ± 5°C (437 ± 9°F) mechanical-convection oven in which air passes the specimens at a velocity of

100 to 200 feet per minute. After conditioning, the specimens shall be removed from the oven, cooled to

room temperature, and visually examined for evidence of dripping, flowing, or cracking.

4.3.4

Heat Aging:

4.3.4.1 Procedure A: Three specimens, prepared and measured in accordance with 4.3.1, shall be conditioned for

168 hours in a 175 ± 5°C (347 ±9°F) mechanical-convection oven in which air passes the specimens at a

velocity of 100 to 200 feet per minute. After conditioning, the specimens shall be removed from the oven,

cooled to room temperature, and tested for tensile strength and ultimate elongation in accordance with

4.3.1.

Tyco Electronics

305 Constitution Dr

Menlo Park, CA

94025, U.S.A.

TITLE:

CAP, SPLICE ENCAPSULATION

DOCUMENT NO.:

Unless otherwise specified dimensions are in millimeters.

[Inches dimensions are shown in brackets]

TOLERANCES:

0.00 N/A

0.0 N/A

0 N/A

DRAWN BY:

ANGLES: N/A

ROUGHNESS

IN MICRON

CAGE CODE:

Raychem

Devices

D-300-08/-12/-18

REV:

DATE:

Tyco Electronics reserves the right to

amend this drawing at any time. Users

should evaluate the suitability of the

product for their application.

ECO NUMBER:

REPLACES:

SCALE:

SIZE:

31-July-08

SHEET:

M. FORONDA

06090

D010044

08-018889

NTS

2 of 7

If this document is printed it becomes uncontrolled. Check for the latest revision.

CUSTOMER DRAWING

4.3.4.2. Procedure B: Three specimens, prepared and measured in accordance with 4.3.1, shall be conditioned for

1000 hours in a 150 ± 3°C (302 ± 5°F) mechanical-convection oven in which air passes the specimens at a

velocity of 100 to 200 feet per minute. After conditioning, the specimens shall be removed from the oven,

cooled to room temperature, and tested for tensile strength and ultimate elongation in accordance with

4.3.1.

4.2.1

Solvent Resistance: Three specimens, prepared and measured in accordance with 4.3.1, shall be

completely immersed in each of the solvents listed in the applicable section of Table 1 for 24 hours at 25 ±

3°C (77 ± 5°F). The volume of the fluid shall be not less than 20 times that of the specimens. After

conditioning, the specimens shall be lightly wiped, and then air-dried for 30 to 60 minutes at room

temperature. The specimens shall then be tested for tensile strength and ultimate elongation in accordance

with 4.3.1.

4.3

Test Procedures – Finished Caps

4.3.1

Test Assembles: Part D-300-12 shall be used to qualify D-300-08, D-300-12 and D-300-18. Fifty-five

specimens shall be made by connecting two wires, MIL- 16878/4-14; with a suitable crimp connector.

Wires shall be 10 ± 1 inches in length. The caps shall be applied in accordance with Thermofit Assembly

Procedure D-300-08/-12/-18.

4.3.2

Dimensions and Dimensional Recovery: Five specimens, as supplied, shall be measured for dimensions in

accordance with ASTM D 876. The specimens shall then be conditioned for ten minutes in a 200 ± 5°C

(392 ± 9°F) oven, quenched in water in less than 35°C (95°F) for at least 30 seconds, wiped dry, and the

appropriate measurements taken.

4.3.3

Insulation Resistance: The specimens shall be immersed to within 3 inches of the lead ends in a water bath

containing 5% by weight of NaCl for a minimum of 30 minutes after which time the insulation resistance

shall be measured between the salt solution and the test leads. The test potential shall be 500 volts D.C.

The readings shall be taken after an electrification time of one minute.

4.3.4

Dielectric Withstanding Voltage: The specimen shall be immersed to within 3 inches of the lead ends in a

water bath containing 5% by weight of NaCl for a minimum of 30 minutes after which time the potential

between the salt water and the test leads shall be raised from 0 to the specified voltage at a rate of 500 volts

per second. This potential shall be maintained for one minute and the voltage reduced to 0.

4.3.5

Temperature Cycling: Fifteen assemblies shall be subjected to 200 cycles. Each cycle shall consist of 20

minutes at 135°C (275°F) and 5 minutes at 240°C (400°F) in mechanical-convection ovens with an air

velocity of 100 to 200 feet per minute past the specimens. The specimens shall be subjected to 20 cycles

per day and shall be maintained at 25

5°C (77 ± 9°F) between test days. After the last cycle, the

specimen shall be cooled to 25

5°C (77 ± 9°F) within one hour and tested for insulation resistance (4.4.3)

and dielectric withstanding voltage (4.4.4).

Tyco Electronics

305 Constitution Dr

Menlo Park, CA

94025, U.S.A.

TITLE:

CAP, SPLICE ENCAPSULATION

DOCUMENT NO.:

Unless otherwise specified dimensions are in millimeters.

[Inches dimensions are shown in brackets]

TOLERANCES:

0.00 N/A

0.0 N/A

0 N/A

DRAWN BY:

ANGLES: N/A

ROUGHNESS

IN MICRON

CAGE CODE:

Raychem

Devices

D-300-08/-12/-18

REV:

DATE:

Tyco Electronics reserves the right to

amend this drawing at any time. Users

should evaluate the suitability of the

product for their application.

ECO NUMBER:

REPLACES:

SCALE:

SIZE:

31-July-08

SHEET:

M. FORONDA

06090

D010044

08-018889

NTS

3 of 7

If this document is printed it becomes uncontrolled. Check for the latest revision.

CUSTOMER DRAWING

4.2.1

Heat Aging: Fifteen assemblies shall be conditioned for 1000 hours at 150

3°C (302

5°F) in a

mechanical-convection oven with an air velocity of 100 to 200 feet per minute past the specimens. After

conditioning, the specimen shall be cooled to 25

5°C (77

9°F) within one hour and tested for insulation

resistance (4.4.3) and dielectric withstanding voltage (4.4.4).

Altitude Immersion: Fifteen assemblies shall be immersed in a water bath containing 5% by weight of

NaCl and placed in a chamber. Wire ends, opposite the cap, shall be within the chamber, but not

submerged. The exposed wire ends shall not be sealed. The chamber pressure shall be reduced to

approximately 1 inch of mercury and maintained for 30 minutes. The chamber pressure shall then be

returned to atmospheric pressure. The insulation assistance shall be measured in accordance with 4.4.3.

This shall constitute one cycle. Two additional environment cycles shall be run. At the end of the third

cycle, the insulation resistance (4.4.3) shall be re-measured, and the dielectric withstanding voltage test

(4.4.4) shall be performed.

Corrosive effect: Two caps, as supplied, shall be placed in the bottoms of two clean ½ x 12 inches test

tubes (one cap per tube). A third tube shall be used for control. A copper-glass mirror, about 1 x ¼ inches

shall be suspended from 6 to 7 inches above the bottom of each tube by a fine copper wire attached to a

cork wrapped in aluminum foil. The corks shall tightly seal the test tubes. The lower 2 inches of each tube

then shall be placed in an oven or oil bath at 175

3°C for 16 hours. After cooling, the mirrors shall be

examined in a good light against a white background. Evidence of corrosion shall be areas of transparency

larger than pinholes in a mirror. Discoloration of the copper film or reduction of its thickness shall not be

considered corrosion. The mirrors shall be vacuum- deposited copper with thickness equal to 10

transmission of normal incident light of 5000 angstroms. They shall be stored in a vacuum and shall be

used for test only if no oxide film is present and the copper is not visibly damaged.

Flammability: Ten assemblies shall be mounted vertically, closed end down, in a draft-free chamber. An 8

x 8 inch piece of tissue paper conforminf to UU-T-450 shall be suspended taut and centered 9 ½ inches

below the test specimen, a minimum of ½ inch from the table top, in such a manner that any dripping

particles will fall on the tissue paper. A standard 1/8” Bunsen burner shall be adjusted to produce a blue

flame approximately 1” high. The tip of the flame shall be applied to the closed end of the test specimen

for 10 seconds. The flame shall then be removed and the specimen shall remain undisturbed until burning

ceases. Failure of more than one specimen to extinguish itself within the time specified or ignition of the

tissue paper caused by dripping of flaming or glowing particles shall be cause for rejection.

4.2.1

Tyco Electronics

305 Constitution Dr

Menlo Park, CA

94025, U.S.A.

TITLE:

CAP, SPLICE ENCAPSULATION

DOCUMENT NO.:

Unless otherwise specified dimensions are in millimeters.

[Inches dimensions are shown in brackets]

TOLERANCES:

0.00 N/A

0.0 N/A

0 N/A

DRAWN BY:

ANGLES: N/A

ROUGHNESS

IN MICRON

CAGE CODE:

Raychem

Devices

D-300-08/-12/-18

REV:

DATE:

Tyco Electronics reserves the right to

amend this drawing at any time. Users

should evaluate the suitability of the

product for their application.

ECO NUMBER:

REPLACES:

SCALE:

SIZE:

31-July-08

SHEET:

M. FORONDA

06090

D010044

08-018889

NTS

4 of 7

If this document is printed it becomes uncontrolled. Check for the latest revision.

D-300-08CS1108 Related Products

	D-300-08CS1108	D-300-12
Description	solder & shield tubing splice Encap. cap 2.03-3.04 dia	terminals splice Encap. cap 3.04-5.08 dia
Manufacture	TE Connectivity	TE Connectivity
Product Category	Solder & Shield Tubing	Terminals
RoHS	Yes	Yes
Type	Splice Caps	C
Factory Pack Quantity	1000	1000

Recommended Resources

Do you know about the new RF vector signal generator?

Interface circuit between DAC0832 and 8-bit CPU

RP5020 series typical application circuit diagram

HW8502 cordless phone mobile phone charging circuit

Computer motherboard circuit diagram 820 1_18

Can a 1-second timer interrupt be achieved using the internal clock?: I want to use G2231 to implement a 1 second timer interrupt and count seconds, minutes and hours in the interrupt function. Can I use the internal clock to do this? Or do I need to connect an external...; helloxieyu Microcontroller MCU

Summary of experience in circuit debugging and troubleshooting: [align=left][b]Overview[/b][/align][align=left][color=rgb(51, 51, 51)]Debugging is necessary for junior electronic engineers at the primary stage, so I have combined several debugging articles and som...; ohahaha PCB Design

Experts’ understanding of analog electronics: As a first-level discipline, electronic science and technology is divided into several second-level disciplines at a higher level: microelectronics and solid-state electronics, circuits and systems. I...; qwqwqw2088 Analogue and Mixed Signal

Power supply selection for F5529 development board: [font=微软雅黑][size=4][color=#ff0000] The power supply of the F5529 development board can be configured in many ways. This diagram is very intuitive[/color][/size][/font]...; wstt Microcontroller MCU

Software and hardware design and implementation of Internet access solution based on DSP: With the development of modern network technology, embedded systems such as single-chip microcomputers and DSPs have an increasing demand for access to the network, such as electric meter systems with...; 咖啡不加糖 DSP and ARM Processors

Regarding the serial port driver, the implementation issue of the serial port receive soft FIFO.: The following structure is defined in the serial port driver to implement the reading of serial port received data. typedef struct __RX_BUFFER_INFO { ULONG Read; /* @field Current Read index. */ ULONG...; LIKEY Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components