HLMP-Pxxx Series, HLMP-Qxxx Series,
HLMP-6xxx Series, HLMP-70xx Series
Subminiature LED Lamps
Data Sheet
Description
Flat Top Package
The HLMP-Pxxx Series flat top lamps use an untinted, non-
diffused, truncated lens to provide a wide radiation pattern
that is necessary for use in backlighting applications. The flat
top lamps are also ideal for use as emitters in light pipe
applications.
Features
Subminiature flat top package
— Ideal for backlighting and light piping applications
Subminiature dome package
— Diffused dome for wide viewing angle
— Non-diffused dome for high brightness
TTL and LSTTL compatible 5V resistor lamps
Available in six colors
Ideal for space limited applications
Axial leads
Available with lead configurations for surface mount
and through hole PCB mounting
Dome Packages
The HLMP-6xxx Series dome lamps for use as indicators use
a tinted, diffused lens to provide a wide viewing angle with a
high on-off contrast ratio. High brightness lamps use an un-
tinted, nondiffused lens to provide a high luminous intensity
within a narrow radiation pattern.
Resistor Lamps
The HLMP-6xxx Series 5 volt subminiature lamps with built
in current limiting resistors are for use in applications where
space is at a premium.
Lead Configurations
All of these devices are made by encapsulating LED chips on
axial lead frames to form molded epoxy subminiature lamp
packages. A variety of package configuration options is
available. These include special sur face mount lead configura-
tions, gull wing, yoke lead or Z-bend. Right angle lead bends at
2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing
are available for through hole mounting. For more information
refer to Standard SMT and Through Hole Lead Bend Options
for Subminiature LED Lamps data sheet.
Broadcom Confidential
-1-
HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series
Data Sheet
Device Selection Guide
Part Number: HLMP-xxxx
Standard
DH AS
Red
AlGaAs Red
P005
P105
P102
6000
Q100
Q105
Q150
Q155
6600
6620
6720
6800
6820
High
Efficiency
Red
P205
P202
6300
6305
7000
Orange
P405
P402
Q400
Q405
Yellow
P305
P302
6400
6405
7019
High Perf.
Green
P505
P502
6500
6505
7040
Emerald
Green
P605
Device
Description
Untinted, Non-diffused,
Flat Top
Untinted, Diffused,
Flat Top
Device
Outline
Drawing
A
A
B
B
B
B
B
B
Q600
Q605
Tinted, Diffused
Untinted, Nondiffused,
High Brightness
Tinted, Diffused, Low
Current
Nondiffused,
Low Current
Tinted, Diffused, Resistor,
5V, 10 mA
Diffused, Resistor, 5V,
4 mA
Package Dimensions
Flat Top Lamps
0.50 (0.020) REF.
1.40 (0.055)
1.65 (0.065)
11.68 (0.460)
10.67 (0.420)
BOTH SIDES
CATHODE
Diffused and Nondiffused
0.50 (0.020) REF.
11.68 (0.460)
10.67 (0.420)
BOTH SIDES
CATHODE
ANODE
ANODE
1.65 (0.065)
DIA.
1.91 (0.075)
0.20 (0.008) MAX.
0.46 (0.018)
0.56 (0.022)
0.25 (0.010) MAX.
NOTE 2
1.65 (0.065)
DIA.
1.91 (0.075)
0.20 (0.008) MAX.
0.46 (0.018)
0.56 (0.022)
0.25 (0.010) MAX.
NOTE 2
2.21 (0.087)
1.96 (0.077)
1.14 (0.045)
1.40 (0.055)
0.18 (0.007)
0.23 (0.009)
0.63 (0.025)
0.38 (0.015)
2.44 (0.096)
1.88 (0.074)
2.21 (0.087)
1.96 (0.077)
0.76 (0.030) R.
0.89 (0.035)
0.94 (0.037)
1.24 (0.049)
2.03 (0.080)
1.78 (0.070)
2.92 (0.115)
MAX.
0.63 (0.025)
0.38 (0.015)
2.08 (0.082)
2.34 (0.092)
0.18 (0.007)
0.23 (0.009)
0.79 (0.031) MAX.
2.08 (0.082)
2.34 (0.092)
0.79 (0.031)
0.53 (0.021)
CATHODE
STRIPE
CATHODE
STRIPE
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD
POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.
Broadcom Confidential
-2-
HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series
Data Sheet
Figure 1: Proper Right Angle Mounting to a PCB to Prevent Protruding Cathode Tab from Shorting to Anode Connection
CATHODE
TAB
NO. ANODE DOWN.
YES. CATHODE DOWN.
Absolute Maximum Ratings (T
A
= 25°C)
HLMP-PXXX Anode/Cathode
Parameter
DC Forward Current
[1]
Peak Forward Current
[2]
DC Forward Voltage
(Resistor Lamps Only)
Reverse Voltage (IR = 100 µA)
Transient Forward Current
(10 µs Pulse)
Operating Temperature Range
Non-Resistor Lamps
Resistor Lamps
Storage Temperature Range
For Thru Hole Devices:
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Reflow Soldering Temperature
–55 to +100
–40 to +100
–55 to +100
–40 to +85
–55 to +100
260°C for 5 seconds
260°C for 20 seconds
–40 to +100
–20 to +100
°C
5
2000
5
500
Standard
Red
50
1000
DH AS
AlGaAs
Red
30
300
High Eff.
Red
30
90
6
5
500
Orange
30
90
Yellow
20
60
6
High Perf.
Green
30
90
6
5
500
Emerald
Green
30
90
6
5
500
Unit
mA
mA
V
V
mA
5
500
5
500
–20 to +85
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this high current.
Broadcom Confidential
-3-
京公网安备 11010802033920号
EEWORLD
