performance and high frequency output, using a low
cost fundamental crystal of between 19-40MHz..
The frequency selector pads of PL680-3X enable
output frequencies of (2, 4, 8, or 16) * F
XIN
. The
PL680-3X is designed to address the demanding
requirements of high performance applications such
Fiber Channel, serial ATA, Ethernet, SAN, etc.
PL680-3X
2
3
4
5
GNDANA
3x3 QFN
Note1: QBAR is used for single ended CMOS output
.
Note2: ^ Denotes internal pull up resistor.
BLOCK DIAGRAM
VCO
Divider
Charge
Pump
+
Loop
Filter
Output
Divider
(1,2,4,8)
GNDBUF
LP
LM
XIN
XOUT
XTAL
OSC
Phase
Detector
VCO
(F
XiN
x16)
QBAR
Q
Performance Tuner
OE
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 11/28/05 Page 1
(Preliminary)
PL680-37/38/39
38-640MHz Low Phase Noise XO
OUTPUT ENABLE LOGICAL LEVELS
Part #
PL680-38 (PECL)
PL680-37 & 39 (CMOS or LVDS)
OE
0 (Default)
1
0
1 (Default)
State
Output enabled
Tri-state
Tri-state
Output enabled
PIN DESCRIPTIONS
Name
VDDANA
XIN
XOUT
SEL2
OE_CTRL
DNC
GNDANA
LP
LM
GNDBUF
Q
VDDBUF
QBAR
GNDBUF
SEL1
SEL0
TSSOP
Pin number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
3x3mm QFN
Pin number
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
Type
P
I
O
I
I
-
P
-
-
P
O
P
O
P
I
I
VDD for analog Circuitry.
Description
Crystal input pin. (See Crystal Specifications on page 3).
Crystal output pin. (See Crystal Specifications on page 3).
Output frequency Selector pin.
Output enable control pin. (See OE_CTRL Logic Levels on page
1).
Do Not Connect
Ground for analog circuitry.
Tuning inductor connection. The inductor is recommended to be
a high Q small size 0402 or 0603 SMD component, and must be
placed between LP and adjacent LM pin. Place inductor as close
to the IC as possible to minimize parasitic effects and to
maintain inductor Q.
GND connection for output buffer circuitry.
PECL or LVDS output.
VDD connection for output buffer circuitry. VDDBUF should be
separately decoupled from other VDDs whenever possible.
Complementary PECL, LVDS output; Or single ended CMOS
output.
GND connection for output buffer circuitry.
Output frequency Selector pin.
Output frequency Selector pin.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 11/28/05 Page 2
(Preliminary)
PL680-37/38/39
38-640MHz Low Phase Noise XO
FREQUENCY SELECTION TABLE
SEL2
0
0
0
0
1
1
1
1
SEL1
0
0
1
1
0
0
1
1
SEL0
0
1
0
1
0
1
0
1
Selected Multiplier/Output Frequency
VCO Max*
VCO Min*
Reserved
Reserved
Fin x 2
Fin x 8
Fin x 16
Fin x 4
All SEL pads have internal pull-ups (default value is ‘1’). Bond to GND to set to 0.
* Special Test Modes to help selecting the inductor value for the target output frequency.
PERFORMANCE TUNING & INDUCTOR VALUE SELECTION
Please refer to PhaseLink’s ‘PhasorV Tuning Assistance’ software to automatically calculate the optimum inductor
values. In addition, the chart below could be used as a reference for quick inductor value selection.
Use the special test modes “VCO Max” and “VCO Min” to determine the optimum inductor value. “VCO Max”
represents the high end of the VCO range and “VCO Min” represents the low end of the VCO range. The output
frequency in the “VCO Max” and “VCO Min” test modes is VCO/16. This means that the output frequencies are
around the crystal frequency that will be used. The optimum inductor value is where the target crystal frequency
is closest to the middle between the “VCO Max” and “VCO Min” output frequencies. In this case the VCO will lock
in the middle of its tuning range with maximum margin on either side.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 11/28/05 Page 3
(Preliminary)
PL680-37/38/39
38-640MHz Low Phase Noise XO
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other
conditions above the operational limits noted in this specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
2. Crystal Specifications
PARAMETERS
Crystal Resonator Frequency
Crystal Loading Rating
Crystal Shunt Capacitance
Recommended ESR
SYMBOL
F
XIN
C
L (xtal)
C
0 (xtal)
R
E
CONDITIONS
Parallel Fundamental Mode
MIN.
19
TYP.
17.7
MAX.
40
5
30
UNITS
MHz
pF
pF
Ω
AT cut
Note:
Crystal Loading rating: 17.7pF is the loading the crystal sees from the XO chip. It is assumed that the crystal will be at nominal frequency at this
load. If the crystal requires less load to be at nominal frequency, then a capacitor can placed in series with the crystal. If the crystal requires more
load to be at nominal frequency, capacitors can be placed from XIN and XOUT to ground. This however may reduce the oscillator gain.
3. General Electrical Specifications
PARAMETERS
Supply Current,
Dynamic (with
Loaded Outputs)
Operating Voltage
Output Clock
Duty Cycle
Short Circuit
Current
Note:
CMOS operation is not advised above 200MHz with 15pF load; and 320MHz with 10pF load.
SYMBOL
I
DD
V
DD
CONDITIONS
PECL/LVDS/CMOS
PECL/LVDS
38MHz<Fout<320MHz
320MHz<Fout<640MHz
MIN.
TYP.
MAX.
65/45/30
90/70
UNITS
mA
V
%
mA
@ 50% V
DD
(CMOS)
@ 1.25V (LVDS)
@ V
DD
– 1.3V (PECL)
2.25
45
45
45
50
50
50
±50
3.63
55
55
55
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 11/28/05 Page 4
(Preliminary)
PL680-37/38/39
38-640MHz Low Phase Noise XO
4. Jitter Specifications
PARAMETERS
CONDITIONS
FREQUENCY
106.25MHz
156.25MHz
212.5MHz
312.5MHz
622.08MHz
106.25MHz
156.25MHz
212.5MHz
312.5MHz
622.08MHz
106.25MHz
156.25MHz
212.5MHz
312.5MHz
622.08MHz
MIN.
TYP.
0.4
0.4
0.4
0.4
0.4
3
3
3
3
6
20
20
20
20
40
MAX.
0.5
0.5
0.5
0.5
0.5
5
5
5
5
8
30
30
30
30
50
UNITS
Integrated jitter RMS
Integrated 12 kHz to 20 MHz
ps
Period jitter RMS
With capacitive decoupling
between VDD and GND.
Over 10,000 cycles.
ps
Period jitter Peak-to-
Peak
With capacitive decoupling
between VDD and GND.
Over 10,000 cycles.
ps
5. Phase Noise Specifications
PARAMETERS
FREQ.
106.25MHz
Phase Noise
relative to carrier
(typical)
156.25MHz
212.5MHz
312.5MHz
622.08MHz
@10Hz
-66
-62
-62
-59
-49
@100Hz
-96
-92
-92
-85
-84
@1kHz
-122
-120
-118
-117
-111
@10kHz
-132
-132
-126
-128
-120
@100kHz
-126
-128
-120
-125
-118
@1M
-144
-140
-140
-139
-128
@10M
-150
-150
-150
-148
-138
dBc/Hz
UNITS
6. CMOS Electrical Characteristics
PARAMETERS
Output drive current
Output Clock Rise/Fall Time
Output Clock Rise/Fall Time
SYMBOL
I
OH
I
OL
CONDITIONS
V
OH
= V
DD
-0.4V, V
DD
=3.3V
V
OL
= 0.4V, V
DD
= 3.3V
0.3V ~ 3.0V with 15 pF load
20%-80% with 50Ω Load
MIN.
30
30
TYP.
MAX.
UNITS
mA
mA
0.7
0.3
ns
ns
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
DIY pedal controller based on Herculese (Part 2): The first draft of the schematic diagram is completed. See the attachment for details. [[i] This post was last edited by tziang on 2013-6-21 15:45 [/i...
What compiler and debugger do you use on your computer? ads1.2? Inbete's IDE? I just bought an abcarm s3c2410 board, but it doesn't come with a compiler. What's the best one? I've only used Inbete bef...
: Test object: A handheld device with S5pv210 +512M DDR2 (4*128M) as the core. Input voltage 10V. uboot main frequency setting #define CONFIG_CLK_1000_200_166_133 CPU: S5PV210@1000MHz(OK) APLL = 1000M...
[i=s]This post was last edited by jorya_txj on 2014-11-29 13:07[/i] Currently, almost all RTOS interrupts are processed in the interrupt context. Even though raw-os provides a mechanism for the lower ...
[b]One: Tesla's dream[/b] There was a piece of news: On August 31, 2010, the International Wireless Power Consortium held a press conference in Beijing and announced the official release of the qi wir...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
