EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-69CS8J5-18RCN

Description
Cable Assembly, 28AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-740-2-69CS8J5-18RCN Overview

Cable Assembly, 28AWG,

177-740-2-69CS8J5-18RCN Parametric

Parameter NameAttribute value
Objectid7005065720
Reach Compliance Codeunknown
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.081 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
Jacket materialETHYLENE-CHLOROTRIFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors69
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.244 Ω
shieldYES
stay7X36
Wire gauge28 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
The upcoming nrf52840 metro express development board
The upcoming nrf52840 development board is compatible with Arduino, with QSPI flash and BTLE on board. It has a native USB interface and supports CircuitPython and Arduino development.[url=https://blo...
dcexpert MicroPython Open Source section
Electronic Instrumentation and Electrical Measurement
Electrical Instruments, Post...
缥缈轮回 Suggestions & Announcements
6 Task Scheduling
[i=s]This post was last edited by Rambo on 2018-8-15 13:29[/i] [color=#4f4f4f][size=14px]uC/OS-II uses a preemptive real-time multitasking kernel. The preemptive real-time kernel runs the highest prio...
兰博 Embedded System
CodeWarrior warning C1420
CodeWarrior gives the following warning message during compilation: Warning: C1420: Result of function-call is ignored. Can anyone tell me what this means and how to solve it? The chip is MC9S08DZ60[[...
kwq498901 NXP MCU
C-SPY sucks, can't set breakpoints...
When setting breakpoints in C-SPY, I always get the error: Error[130]: "some breakpoint could not be set", no matter which statement I set it on, it can't be set.??? ??? ??? ??? ??? ??? ??? ??? ??? ??...
ladeng Microcontroller MCU
How does ulink2 power the board? How do I set it up?
[i=s] This post was last edited by paulhyde on 2014-9-15 03:48 [/i] How can I power the arm board with ulink2? How do I set it up? Does anyone know? Please help me...
hua19900322 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2466  1638  2284  2879  2150  50  33  46  58  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号