EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-67GS8J1-18SZN

Description
Cable Assembly, 28AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-5-67GS8J1-18SZN Overview

Cable Assembly, 28AWG,

177-740-5-67GS8J1-18SZN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005115648
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL9.35
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.081 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.244 Ω
shieldYES
stay7X36
Wire gauge28 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
From principle to design, it is very simple. LED circuit board design description
In the process of designing LED power supply, we usually put the physical design of PCB board in the last link. If the design method is not appropriate, PCB may radiate too much electromagnetic interf...
sppcb1 LED Zone
1. Initial exploration of SensorTile and BlueMS experience
[size=3]【一】SensorTile Introduction:[/size] [size=3] The SensorTile kit is a multifunctional and highly integrated development platform, which includes a system core board, a bracket expansion board, a...
hanyeguxingwo MEMS sensors
If a quadcopter has a flight control problem, can the flight control chip be used?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:10[/i] If a quadcopter has a flight control problem, can the flight control chip be used?...
xilin1991 Electronics Design Contest
Hey guys, I'm making a temperature and humidity sensor, using the DHT21 sensor, but there is a program that has been bothering me for a long time...
Function name: Read temperature and humidity bytes Function: Read each byte of temperature and humidity Description: None **********************************************************/ void COM(void)//Re...
安之若素h 51mcu
Urgent: How to access DAC8571 via I2C module with LM3S8962? Why is it not working?
[i=s]This post was last edited by dontium on 2015-1-23 13:42[/i]First, let me introduce the DAC8571 data; it is a digital-to-analog DAC, with an operating voltage of 3.3V and a current reference volta...
eeleader Analogue and Mixed Signal
NTP network timing programming big endian and small endian storage
Recently, I encountered a problem while learning NTP network timing programming. This is a problem that is easily overlooked by us, but it is also a very important problem. Students who have some unde...
Hellovictoria Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1294  561  1626  48  1797  27  12  33  1  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号