891-041-51ST01-285-6S datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 891-041-51ST01-285-6S

891-041-51ST01-285-6S: DescriptionCable Assembly; CategoryThe connector Connector bracket; File Size251KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

891-041-51ST01-285-6S Overview

Cable Assembly

891-041-51ST01-285-6S Parametric

Parameter Name	Attribute value
Objectid	7008195613
Reach Compliance Code	compliant
Connector bracket type	CABLE ASSEMBLY

Preview

Download Datasheet

View All

nAno rectAngulAr to AlphAlink Flex jumpers

Contact arrangements

rectangular nano to alphalink flex Jumpers

Glenair series 89 rectangular Nanominiature connectors available in 6 contact arrangements,

terminated with rugged polyimide-based flex to AlphaLink board level connectors.

Rectangular Nano

to AlphaLink

flex jumper

Recommended Rectangular Nano I/O to AlphaLink Contact Arrangements*

15P

21P

15S

21S

10 Contacts

16 Contacts

24 Contacts

4x R .033 Max

.155

+.005

-.000

25P

31P

M+.010/-.000

Recommended Panel Cutout

2x Ø .096 +.006

-.000

Thru

.150

25S

31S

Ø .042 Typ

Pads

.050 Typ

.025

.050

2x .080 Thru

Mounting Holes

Recommended PCB Layout

28 Contacts

32 Contacts

37P

51P

* These are recommended contact

arrangements only, but do offer best

availability. Contacts are mapped 1-to-1

from i/O to B/L connector (unused B/L

contacts not connected). For alternative

wire schedules, please consult factory.

37S

51S

40 Contacts

To optimize the 40-contact AlphaLink board level

connector, 40 contacts of a 51-contact size Nano

connector can be used.

Recommended Resources

High performance antenna amplifier circuit c

Try making SRS effector circuit diagram using op amp

RC circuit detects reverse sequence

Battery low voltage detection circuit diagram

Low-power three-terminal voltage regulator application circuit diagram

STK075 power amplifier circuit

WINCE automatically runs application program when booting: Problem with automatic application running on WINCE startup I tried to make my application (MyApp.exe) automatically run on startup according to the following method, but it was unsuccessful. After st...; happywar Embedded System

Remote system upgrade: [b][font=楷体,楷体_GB2312][size=5]When updating the FPGA remotely via the network port, what file format should be written to the EPCs? [/size][/font][/b]...; hzwhg001 FPGA/CPLD

Please explain the meaning of the third sentence below: [size=5]Datain: in std_logic; signal Data_Buf: std_logic_vector(15 downto 0); Data_Buf <= Data_Buf(Data_Buf'high - 1 downto 0) & Datain; I don't understand vhdl language, please help me explain the ab...; kready FPGA/CPLD

LM3886 Power Amplifier PCB and Schematic: LM3886 Power Amplifier PCB and Schematic...; hesoka Analogue and Mixed Signal

PIC microcontroller has been in the interrupt service routine: I used the PIC I/O port interrupt in my program. I turned off the general interrupt in the interrupt service program and turned it on again after execution. I did not generate any level changes in the...; 爱好汽车电子 Microchip MCU

【CN0062】Interface between ADL5382 demodulator and AD9262 ADC to realize RF to bit stream solution: Circuit Function and Advantages This two-chip solution consisting of the ADL5382 and the AD9262 provides an RF-to-bits solution with optimized performance, low cost, and minimal board space. The two-c...; EEWORLD社区 ADI Reference Circuit

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components