EEWORLDEEWORLDEEWORLD

Part Number

Search

A1142LUATI-T4

Description
sensitive two-wire chopper-stabilized unipolar hall effect switches
File Size344KB,13 Pages
ManufacturerAll Sensors
Download Datasheet Compare View All

A1142LUATI-T4 Overview

sensitive two-wire chopper-stabilized unipolar hall effect switches

A1140, A1141, A1142, and A1143
Sensitive Two-Wire Chopper-Stabilized
Unipolar Hall Effect Switches
Features and Benefits
Chopper stabilization
Low switchpoint drift over operating
temperature range
Low sensitivity to stress
Factory programmed at end-of-line for optimized
switchpoints
On-chip protection
Supply transient protection
Reverse-battery protection
On-board voltage regulator
3.5 to 24 V operation
Description
The A1140, A1141, A1142, and A1143 devices are sensitive,
two-wire, unipolar, Hall effect switches that are factory-
programmed at end-of-line to optimize magnetic switchpoint
accuracy. These devices use a patented high frequency chopper-
stabilization technique, produced using the Allegro advanced
BiCMOS wafer fabrication process, to achieve magnetic
stability and to eliminate offset inherent in single-element
devices exposed to harsh application environments.
Commonly found in a number of automotive applications,
these switches are utilized to sense seat track position,
seat belt buckle presence, hood/trunk latching, and shift
selector position. Two-wire unipolar switches, such as the
A1140/41/42/43 family, are particularly advantageous in
price-sensitive applications because they require one less
wire for operation than do switches with the more traditional
open-collector output. Additionally, the system designer
inherently gains diagnostics because there is always output
current flowing, which should be in either of two narrow
ranges. Any current level not within these ranges indicates a
fault condition. The A1140/41/42/43 family of switches also
Packages: 3 pin SOT23W (suffix LH), and
3 pin SIP (suffix UA)
Continued on the next page…
Not to scale
Functional Block Diagram
V+
VCC
Regulator
To All Subcircuits
0.01 uF
Dynamic Offset
Cancellation
Clock/Logic
Sample and Hold
Low-Pass
Filter
Amp
GND
Package UA Only
GND
A1140-DS, Rev. 8

A1142LUATI-T4 Related Products

A1142LUATI-T4 A1140LUATI-T4 A1141 A1141EUATI-T4 A1141LUATI-T4 A1142 A1142EUATI-T4
Description sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches sensitive two-wire chopper-stabilized unipolar hall effect switches
Find a job
[:$]I am a high school student who has been studying for a year and a half. Now I don’t know what kind of job I should do. Can you give me some advice on what good jobs are suitable for me now?...
weili Recruitment
Problems of using thyristor to control the starting resistance
What should I do if I connect a circuit that uses a thyristor to control the starting resistor and turns off the starting resistor after starting?...
yaya Power technology
FPGA frequency division problem
My board is SPARTAN-3E XC3S250E, 50MHZ system clock. I want to divide it by 2 to get 25MHZ clock and then output it through the controller. But no matter I use the frequency divider or DCM to divide i...
苏醒的小毛驴 FPGA/CPLD
S2E routine entry analysis
Recently, several netizens have been concerned about some issues with the S2E routines. I would like to write down some of my thoughts here, hoping that it will be of some help to you.First post a pic...
academic Microcontroller MCU
ATMEGA8 strange problem
The situation I encountered was that the program did not run at first. I checked the crystal oscillator with an oscilloscope and found a waveform. But I didn't know why it didn't run. Later, I used a ...
wellge Embedded System
The boot logo disappeared?
I'd like to borrow your domain name. I created an area on NAND to store the logo. In OEMPlatformInit() in Eboot, I first read the logo into RAM and then displayed the logo. However, it disappeared aft...
jiangyebula Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 511  2710  1633  1211  961  11  55  33  25  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号