Y1726152K000T0L datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y1726152K000T0L

Y1726152K000T0L: DescriptionFixed Resistor, Metal Foil, 1W, 152000ohm, 500V, 0.01% +/-Tol, -2,2ppm/Cel,; CategoryPassive components The resistor; File Size112KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

Y1726152K000T0L Overview

Fixed Resistor, Metal Foil, 1W, 152000ohm, 500V, 0.01% +/-Tol, -2,2ppm/Cel,

Y1726152K000T0L Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	978490817
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Hermetically Sealed
JESD-609 code	e0
Lead diameter	0.64 mm
Lead length	25.4 mm
Number of terminals	4
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package diameter	12.7 mm
Package length	25.4 mm
Package form	4 Terminals
method of packing	Bulk
Rated power dissipation(P)	1 W
resistance	152000 Ω
Resistor type	FIXED RESISTOR
series	H SERIES-OTHER
technology	METAL FOIL
Temperature Coefficient	2 ppm/°C
Terminal surface	Tin/Lead (Sn/Pb)
Tolerance	0.01%
Operating Voltage	500 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishay.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 07-Dec-09

For any questions, contact:

foil@vishay.com

www.vishay.com

Recommended Resources

Isolated RS-485 interface circuit

Power delay turn-on controller circuit

Door opening alarm circuit diagram

Visitors call the door light

Photoelectric control circuit for pen tip slit control

Field output circuit: TDA8351AQ

WinCE LCD driver VBPD, VFPD and other parameters calculation: The LCD driver of the smdk2410 I use has the following code //TFT timing parameter for V16C6448AB(PRIME VIEW) #define VBPD ((1-1)&0xff) #define VFPD ((2-1)&0xff) #define VSPW ((2-1) &0x3f) #define HBP...; shenyu815 Embedded System

The permissions of the automatically generated node tty0 are w, how to change it to rw?: rt................tty0 should be automatically generated by tty, I don't know why the permission is w; I want to know how to change it...; 那时年少 Embedded System

Old Boy-Chopstick Brothers: Old Boy - Chopstick Brothers Old Boy Movie Soundtrack by: Luan Dou LuanThat's the person I miss day and night I love deeplyHow should I express it, will she accept meMaybe I will never say that to her...; drjloveyou Talking

What is the best solution for a DCDC with an input voltage of 35V to 55V, an output voltage of 100V, and a rated power of 500W?: [size=5]I don't know how to make power supplies[/size]{:1_142:}[size=5]My colleague used a microcontroller to control MOS to boost directly... The effect was not ideal... Does anyone have a small and ...; 飞鸿浩劫 Power technology

TIOBE Index October 2022: TIOBE Index October 2022Headline: The dominance of the four major languages continues to increaseFor quite some time, Python, Java, C and C++ were the top four languages in the TIOBE index. They are f...; dcexpert Talking

How can I use the TPS40210 boost chip to make a boost adjustable power supply using WEBENCH?: I have used WEBENCH myself, but I found that its output terminals are all fixed values. If I want to make an adjustable output, WEBENCH doesn't seem to work. The original buck circuit using TPS5434 ca...; 良晴先生 Analogue and Mixed Signal

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components