EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GG-00-3242-F

Description
Fixed Resistor, Thin Film, 0.25W, 32400ohm, 100V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GG-00-3242-F Overview

Fixed Resistor, Thin Film, 0.25W, 32400ohm, 100V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP

B0202GG-00-3242-F Parametric

Parameter NameAttribute value
Objectid1579393373
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance32400 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal shapeONE SURFACE
Tolerance1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Purgatory Legend-RAM War
Calling and verifying IP core RAM...
雷北城 FPGA/CPLD
【Altera SoC Experience Tour】High-speed Data Acquisition System Design
[i=s]This post was last edited by chenzhufly on 2015-3-26 00:14[/i] [align=center][size=4][b]Author: chenzhufly QQ[/b][b]: 36886052[/b][/size][/align][align=left][size=4][b]1. Hardware environment[/b]...
chenzhufly FPGA/CPLD
Looking for a Verilog solution?
[color=#FF0000]Timer for competition (with reset button, start/pause button, 4 digital tubes)[/color] Please write it in Verilog language!!!...
jbcfelix Embedded System
Re-understanding of analog ground and digital ground
In order to achieve good anti-interference, we often see ground splitting wiring on PCB boards. However, not all digital circuits and analog circuits must be split on the ground plane. Because this sp...
xiefei FPGA/CPLD
Problems with CRect and RECT
If I assign a CRect object to a RECT object, will there be any problems? For example, if a function parameter is of type RECT, but a CRect object is passed in as a parameter, will there be any problem...
emaster Embedded System
Matrix keyboard
Why when I turn on the switch when scanning the matrix keyboard, it always displays 0, which is the number of the keys in the first row and first column. It should display nothing. I can't figure it o...
Learner_new 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 456  1971  1452  2387  353  10  40  30  49  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号