EEWORLDEEWORLDEEWORLD

Part Number

Search

XSC32005100AH

Description
RES,SMT,THIN FILM,510 OHMS,100WV,2.5% +/-TOL,-50,50PPM TC,0505 CASE
CategoryPassive components    The resistor   
File Size139KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XSC32005100AH Overview

RES,SMT,THIN FILM,510 OHMS,100WV,2.5% +/-TOL,-50,50PPM TC,0505 CASE

XSC32005100AH Parametric

Parameter NameAttribute value
Objectid1175265117
package instructionSMT, 0505
Reach Compliance Codeunknown
ECCN codeEAR99
YTEOL7.85
structureChip
Manufacturer's serial numberSC3
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length1.27 mm
Package formSMT
Package width1.27 mm
method of packingTray
Rated power dissipation(P)0.4 W
resistance510 Ω
Resistor typeFIXED RESISTOR
seriesSC3
size code0505
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Tolerance2.5%
Operating Voltage100 V
SC3
Vishay Electro-Films
NiCr Thin Film, Top-Contact Resistor
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Small single chip size: 0.050 inches square
Resistance range: 100
Ω
to 50 kΩ
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
400 mW capability
User trimmable
The SC3 series resistor chips on silicon offer a combination
of nichrome stability, wide resistance range and higher
power rating than is available on the same sized ceramic
substrate.
The SC3’s are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The SC3s are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI SC3 chip resistors have excellent power dissipation capability and are ideally suited for prototyping.
Typical application areas are:
Amplifiers
Couplers
Oscillators
Filters
Attenuators
Recommended for hermetic environments where die is not exposed to moisture.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.1 %
PROCESS CODE
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
CLASS H*
202
200
201
*MIL-PRF-38534 inspection criteria
CLASS K*
206
204
205
100
Ω
50 k
Ω
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
Stability, 1000 h, + 125 °C
Operating Temperature Range
ThermalShock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 150 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
- 20 dB typ.
± 0.1 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.25 % max.
ΔR/R
± 0.25 % max.
ΔR/R
200 V
10
12
min.
100 V max.
400 mW
± 0.25 % max.
ΔR/R
www.vishay.com
46
For technical questions contact: efi@vishay.com
Document Number: 61014
Revision: 12-Mar-08
High-speed operational amplifier cascade self-excitation
[i=s]This post was last edited by dontium on 2015-1-23 11:37[/i] In a high-speed signal chain, I use two stages of OPA820 as preamplifiers. The two stages amplify 10 times respectively. They are conne...
hnlichong Analogue and Mixed Signal
【Perf-V Review】Lighting Experiment
[i=s]This post was last edited by eew_3sqZMg on 2021-1-21 14:02[/i]Xilinx's Vivado has been installed, but everything is still unfamiliar. The toolbar is simple but not simplistic. The column on the l...
eew_3sqZMg FPGA/CPLD
Do you have any dsp boards for sale?
Looking to buy DSP development board. I have STM32 development board from Zhengdian Atom, Ruisha, 51 microcontroller and TI board, which can be interchanged....
908508455a Buy&Sell
Ask the moderator: About Serialwire debugging
STM32 has two debugging modes, JTAG interface and serial interface. Is the serial interface the debug port?I read in the documentation thatoutput a specified JTAG sequence on TMS/TCK(mapped to SWDIO a...
mrking0105 stm32/stm8
【TI's First Low Power Design Competition】The Second Batch of Shortlisted
[size=5]The second batch of shortlisted candidates for TI's first low-power design competition: [/size] [size=5]cmyti123, neehamwu, zsz123, yuqishu, iwqtthf, wangyuchao, biciny, yiya, shallowmy, hankf...
maylove Microcontroller MCU
The LCD and GPIO are initialized, the LCD displays normally, why is the LED not on?
When the phenomenon occurs, after both are initialized, the LCD can display normally, but the LED light does not light up. Then I shield the LCD initialization program, and then the light can light up...
小小小小菜鸟 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1183  2478  1940  1915  559  24  50  40  39  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号