EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

NRC02F1963TRF

Description
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 196000ohm, 25V, 1% +/-Tol, -200,200ppm/Cel, 0201,
CategoryPassive components    The resistor   
File Size532KB,6 Pages
ManufacturerNIC Components Corp
Environmental Compliance
Download Datasheet Parametric View All

NRC02F1963TRF Overview

Fixed Resistor, Metal Glaze/thick Film, 0.05W, 196000ohm, 25V, 1% +/-Tol, -200,200ppm/Cel, 0201,

NRC02F1963TRF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7149532606
package instructionSMT, 0201
Reach Compliance Codecompliant
Country Of OriginJapan, Mainland China, Taiwan
ECCN codeEAR99
YTEOL7.9
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.25 mm
Package length0.6 mm
Package formSMT
Package width0.3 mm
method of packingTR, PAPER, 7 INCH
Rated power dissipation(P)0.05 W
Rated temperature70 °C
GuidelineAEC-Q200
resistance196000 Ω
Resistor typeFIXED RESISTOR
size code0201
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient200 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage25 V
[Xiao Meige FPGA Advanced Tutorial] Chapter 9 Serial Oscilloscope Download Based on Serial Port Hunter Software
[b]4. Basic Principles of DDS[/b] [color=#000][size=15px]Note: The content of this article is excerpted from the textbook "EDA Experiment and Practice" written by Zhou Ligong, pages 196-197. [/size][/...
芯航线跑堂 FPGA/CPLD
The minimum input voltage of a single-supply VI converter op amp is related to the load
[i=s]This post was last edited by 1nnocent on 2021-4-9 09:08[/i]The schematic diagram is as follows: If the input of a single-power op amp is not rail-to-rail, the op amp cannot input a signal close t...
1nnocent Analog electronics
Show the WEBENCH design process + multi-channel load power supply design solution
Designing a multi-load power supply using WEBENCH Design requirements: Design a 3-way power supply. Input range DC18V~DC26V, output 5V@2A, 3.3V@1A, [email]1.9V@0.5A[/email] three-way power supply. Amo...
ltbytyn Analogue and Mixed Signal
Analyze the internal circuit of an LED bulb
[backcolor=rgb(239, 245, 249)][size=14px]This is the internal circuit of an LED bulb I copied. I don't quite understand it. The output voltage of the bridge stack should be 310V. Why is such a small c...
House1989 Analog electronics
What are the pull-up and pull-down capabilities of a 0-10V dimmer?
What are the pull-up and pull-down capabilities of a 0-10V dimmer? I want to connect 100 dimmer power supplies in parallel. Will the dimmer's driving capacity be insufficient?...
ckf茉莉花 LED Zone
Some tips for protel
1: When laying out the board, first shrink the wiring area, hold down the right button, and see if the drawing board can be moved up, down, left, and right. If not, move it in the opposite direction u...
歹匕示申 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1766  414  1757  1735  857  36  9  35  18  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号