EEWORLDEEWORLDEEWORLD

Part Number

Search

3VT35/1JND12(105)

Description
EDGE CONNECTOR,PCB MNT,RECEPT,70 CONTACTS,0.1 PITCH,WRAP POST TERMINAL
CategoryThe connector    The connector   
File Size535KB,5 Pages
ManufacturerCooper Industries
Download Datasheet Parametric View All

3VT35/1JND12(105) Overview

EDGE CONNECTOR,PCB MNT,RECEPT,70 CONTACTS,0.1 PITCH,WRAP POST TERMINAL

3VT35/1JND12(105) Parametric

Parameter NameAttribute value
Objectid1225113515
Reach Compliance Codeunknown
ECCN codeEAR99
YTEOL5.8
Other featuresNONE
body width0.37 inch
subject depth0.71 inch
body length3.76 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationAU ON NI
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleBELLOWED TYPE
Dielectric withstand voltage650VAC V
maximum insertion force2.78 N
Insulation resistance5000000000 Ω
Insulator colorGREEN
insulator materialDIALLYL PHTHALATE
MIL complianceYES
Manufacturer's serial numberJND
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityMIL-C-21097
Terminal length0.165 inch
Terminal pitch2.54 mm
Termination typeWIRE WRAP
Total number of contacts70
Evacuation force-minimum value.278 N
Ask a question about SIM3OO
The protector made of 430 MCU and SIM300 module uses SMS to control the device. Now there is a problem. When the protector is powered off, the device will not execute the command when it is turned on,...
zhaohuaipu Embedded System
Is there a 0805 chip resistor package?
Newbie, looking for 0805 package, using AD13...
蛋蛋111111 PCB Design
Differential amplifier circuit--Questions about single-ended output
I have a question when looking at differential amplifier circuits. Differential amplifiers eliminate temperature drift based on the symmetry of the circuit. Wouldn't it be meaningless if it were a sin...
545934451 Analog electronics
Can I use the I2C interface with other sensors after turning on DMP on mpu6050? Will there be any conflict if we share them?
Can I use the I2C interface with other sensors after turning on DMP for mpu6050? Will there be conflicts if they are shared? Note: I use the 6050 with DMP turned on to enable the pedometer function. W...
wumoo Sensor
Introduction to CAN, I2C, I2S, ISP, SSP bus
I found it online and thought it was good, so I’m sharing it here. I also downloaded MARK...
ddllxxrr Microcontroller MCU
ZYNQ collects waveforms of LTC2325-16
@xkl5599 saved it during debugging, for reference....
littleshrimp FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2442  429  1847  2040  1674  50  9  38  42  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号