2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
MP2 Series
End-to-end stackable
Offset dual-beam contact minimizes insertion force
Expanded pin counts
Protective Push-Cap
Monoblockable
Press or heat stake peg
12 mm modular units
Meets global IEC 61076-4-104 Futurebus+
®
standard
See the Regulatory Information Appendix (RIA)
in the “RoHS compliance” section of
www.3Mconnector.com for compliance
information (RIA E1 & C1 apply)
Date Modified: May12, 2010
TS-1115-C
Sheet 1 of 4
Physical
Insulation:
Flammability: UL 94V-0
Material: High Temp LCP
Color: Beige
Contact:
Underplating: 50 μ” (1.27 μm) Nickel
Plating:
Material: Copper Alloy
Wiping Area: See Ordering Information
Solder Tails: See Ordering Information
Electrical
Current Rating:
Signal: 1.5 A - All contacts simultaneously
Insulation Resistance:
10
3
MΩ
Withstanding Voltage:
1,000 V
AC
Environmental
Temperature Rating:
-55° C to 125° C
Process Temperature Rating:
260°C (Profile per J-STD-020C)
Moisture Sensitivity Level:
1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
MetPak is a trademark of 3M Company.
Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE)
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
MetPak
™
2-FB Socket
"A"
1.00
.039
9.30
.366
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
21.0
.83
12.45
.490
MP2 Series
11.80
.465
X
2 1
"D" POST LENGTH
13.50
.531
2.00
.079
TYP.
"C" TAIL LENGTH
6.00
.236
2.00
.079
TYP.
"B"
4 ROW PRODUCT
23.0
.91
ROW
E
D
C
B
A
11.30
.445
12.45
.490
mm
(Inch)
Tolerance Unless Noted
FOR SPECIAL MONOBLOCKS
CONTACT 3M SALES
REPRESENTATIVE
13.80
.543
mm
0
±3
0.0
±0.3
0.00
±0.13
( ) Dimensions used for
Reference Only
1.00
.039
5 ROW PRODUCT
8.00
.315
Note:
1. Refer to IEC 61076-4-104 Futurebus+
®
global standard.
2. “Press Fit” describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated
through-hole (PTH) in a printed circuit board, typically a “back plane.”
Ordering Information
MP2 - SXXX - X1XX - X - XXXX
Contact Count
(See Table 1)
Plating Options:
(See Table 3)
C = Capped Solder Tail
Blank = Press-Fit
Rows
4 = 4 Rows
5 = 5 Rows
Termination Style
M = Solder Tail (Press Peg)
(press peg requiring arbor press for PCB assembly)
(Contact 3M Sales Rep)
P = Press Fit (w/ Tail Cover)
Tail Length
(See Table 2)
TS-1115-C
Sheet 2 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
MetPak
™
2-FB Socket
Pin
Count
024
048
072
096
120
144
168
192
030
060
090
120
150
180
210
240
Dim “A”
mm (Inch)
11.95
23.95
35.95
47.95
59.95
71.95
83.95
95.95
11.95
23.95
35.95
47.95
59.95
71.95
83.95
95.95
[0.471]
[0.943]
[1.415]
[1.889]
[2.36]
[2.833]
[3.305]
[3.778]
[0.471]
[0.943]
[1.415]
[1.888]
[2.361]
[2.833]
[3.305]
[3.778]
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
Table 1 - Connector & Row Lengths
Dim “B”
mm (Inch)
10.00
22.00
34.00
46.00
58.00
70.00
82.00
94.00
10.00
22.00
34.00
46.00
58.00
70.00
82.00
94.00
[0.394]
[0.866]
[1.339]
[1.811]
[2.283]
[2.756]
[3.228]
[3.701]
[0.394]
[0.866]
[1.339]
[1.811]
[2.283]
[2.756]
[3.228]
[3.701]
Rows
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
Block
Count
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
MP2 Series
Table 2 - Tail & Post Lengths
Contact-to-PC
Board Tail Termina-
tion Option No.
Solder
M1
M2
P1
*Compliant-Pin Tail
Table 3 - Plating
Plating Suffix
TG30
Dim “C”
Dim. “D”
Press-Fit*
2.72 [0.107]
3.53 [0.139]
3.57 [0.141]
3.57 [0.141]
Press-Fit Tails*
(RIA E2 & C2 apply)
Solder Tails
(RIA E3 & C2 apply)
Plating Composition
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
0.25 μm [10 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. Matt Whisker Mitigating Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. Matt Whisker Mitigating Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. Matt Whisker Mitigating Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR30
(RIA E2 & C2 apply)
(RIA E3 & C2 apply)
FJ
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
KR
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
LR
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
*Compliant-Pin Tail
TS-1115-C
Sheet 3 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
MetPak
™
2-FB Socket
2.00
.079
2.00
.079
TYP.
3X
6.00
.236
4.00
.157
1.00
.039
4.00
.157
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
THESE HOLES CONSTITUTE MODULAR
REPEATING PATTERN
MP2 Series
A1
UNPLATED THROUGH-HOLE
"B"
12.00
.472
2.05
+.05
-.00
Ø
0.10
.081
+.002
-.000
UNPLATED THRU HOLE
Ø
UNPLATED THROUGH-HOLE
Ø
"D" PLATED THRU HOLE
“D” PLATED THROUGH-HOLE
Ø
0.10
3.00
.118
1.50
.059
+.10
-.00
+.004
-.000
Ø
0.10
UNPLATED THROUGH-HOLE
2.00
.079
4X
8.00
.315
RECOMMENDED 4 ROW PCB HOLE
MOUNTING PATTERN
RECOMMENDED 5 ROW PCB HOLE
MOUNTING PATTERN
Table 4 -- HOLE PLATING For TG30 and TR30 FINISHES ONLY
HOLE
“D”
Finished Dia.
mm [in]
0.65-0.80 [.0256-.0315]
Cu Thickness
mm [in]
0.025 [.001] min
SnPb Thickness
microns [μ”]
15 [600] max
Drilled Hole Dia.
mm [in]
0.81-0.86 [.0319-.0339]
Table 5 -- HOLE PLATING For KR and LR FINISHES ONLY
HOLE
Finished Dia.
mm [in]
0.700-0.800
[.0276-.0315]
Cu Thickness
mm [in]
0.025-0.045
[0.001-0.002]
Immersion Matte Sn
Thickness
microns [μ”]
0.5 - 2.5
[20 - 100]
Electrolitic Au
Thickness
microns [μ”]
0.1 - 0.5
[4 - 20]
OSP ENTEK
Thickness
microns [μ”]
0.2 - 0.5
[8 - 20]
Drilled Hole Dia.
mm [in]
0.830-0.860 [.0330-.0340] or
0.85mm [ #66 ] TWIST DRILL
“D”
TS-1115-C
Sheet 4 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of
ninety (90) days
from the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
The picture below is the PCB board I drew. The middle of the circle is empty. I want to remove the middle of the circle using Design-BOARD SHAPE. How can I do it?...
This evaluation experiment uses ACM32F070 for CAN communication. In the experiment, the USBCAN tool box of Guangcheng Technology and the host computer GCAN are used as a host computer CAN node. The fo...
[size=6] In the TMS320C672X chip manual, the power-on sequence of the core and IO of TI's DSP chip is explained. In the data manual of TMS320C6713 and TMS320DM642, there is also a paragraph saying tha...
I bought a 4.3-inch TFT LCD online. It is a 24-bit color LCD from Donghua.I would like to ask the moderator and netizens:1. How can I use STM32 to drive this LCD?Can I use FSMC?2. STM32 does not have ...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility?
1. The following systems should pay special attention to anti-...[Details]
In the TV monitoring system, in order to complete the collection of information from various information points (video, audio, alarm signal) and the control of various front-end devices (PTZ, lens,...[Details]
1. Fully understand the design requirements of all parties and determine the appropriate solution.
When starting a hardware development project, the original driving force will come from many a...[Details]
For a long time, my country has implemented "community-style collective heating" for hot water heating, and settled accounts based on the heating area, regardless of whether the user uses heat. Thi...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
