EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AA-02-6981-C

Description
Fixed Resistor, Thin Film, 0.25W, 6980ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AA-02-6981-C Overview

Fixed Resistor, Thin Film, 0.25W, 6980ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP

B0202AA-02-6981-C Parametric

Parameter NameAttribute value
Objectid1579350269
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance6980 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
What software do you need to learn for development?
To sum up, the main ones are as follows 1 ADS debugging is ADS AXD to be exact. ADS contains AXD. Originally, we all used SDT, but ARM stopped supporting SDT and changed to support ADS. So we should s...
songrisi Embedded System
A complete collection of lab circuits with evaluation boards
I believe everyone wants to know which of the ADI laboratory circuit recommended download materials can provide evaluation boards. Today we will give you a complete list of laboratory circuits that ca...
EEWORLD社区 ADI Reference Circuit
Problems with the LI command of DMC1824?
Between two LI commands, the axis is hard stopped, without deceleration. I also used AM command in between, but it didn't work, unless I wrote two programs #B, #C, each with one LI, it can decelerate ...
eeleader Industrial Control Electronics
[SAM R21] SAM R21 Xplained Hardware Analysis (Part 4)
[i=s] This post was last edited by dcexpert on 2015-1-28 23:33 [/i] [b]Others [/b] We have analyzed the main hardware modules before, and now we are analyzing the remaining parts. [list] [*]Buttons an...
dcexpert Microchip MCU
MSP430 program burning problem
Hello everyone,I am working on a PCB recently. When I wrote the program, I specified the chip as F1481 and generated a TI TXT format file.Now when I am working on the hardware, I choose to use F1471. ...
istbchbn Microcontroller MCU
Newbie help how to implement USB function
The project I am working on is a car navigation multimedia system. The motherboard is Pxa270. Now I want to add a usbhost driver. I don't know how to modify it in the PB project. Is the driver generat...
yangbh Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1129  2284  2037  1154  2838  23  46  41  24  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号