PH1-MLASA2725 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-MLASA2725

PH1-MLASA2725: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-MLASA2725 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-MLASA2725 Parametric

Parameter Name	Attribute value
Objectid	1871061568
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Connection Type	SC/UPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1531 nm
Nominal optical power output	1.584 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Downhole oxygen concentration detection circuit

Lightning protection wiring for direct-match generators of 300kW and below b

Simple dimming pull switch circuit

MLX10803 application circuit

Night vision benchmark circuit

555 wide range digital capacitive oil meter circuit

Why do people use IAR recently? Is there anything wrong with MDK?: I recently noticed that most of the routines released by TI, ST and other manufacturers for their MCUs are from IAR. It may be that everyone is using IAR. Does MDK have any disadvantages? Can IAR be d...; 90houyidai MCU

PYB Nano UF2 bootloader beta version: In order to facilitate the use of UF2, the UF2 Bootloader of the PYBNano board is specially compiled. You only need to download the dfu firmware to the PYB Nano development board through the DFU metho...; dcexpert MicroPython Open Source section

Raspberry Pi turns into a classic Famicom: [i=s]This post was last edited by zcgzanne on 2016-9-14 11:23[/i] [align=left][font=宋体]During a group chat[/font]NMG[font=宋体] mentioned Raspberry Pi[/font], and[font=宋体]I said that I had installed my ...; zcgzanne DIY/Open Source Hardware

[I contribute to the XILINX Resource Center] Summary of FPGA-specific terms: Summary of FPGA-specific termsVery helpful for beginners! ~...; wanghongyang FPGA/CPLD

Using timer to realize DA function: I am currently working on a wireless intercom and want to use a timer to implement the DA function. The microcontrollers of both boards are MSP430F2012. Board A uses AD to sample microphone signals, a...; wangyg007 Embedded System

Beidou II Positioning System: Satellite navigation receiver: What is the best positioning accuracy for Beidou B3 frequency? Military receivers may have better positioning accuracy, which is said to be able to achieve 2.5-meter pos...; xxhhzz Integrated technical exchanges

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components