EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-NLASC2725

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-NLASC2725 Overview

Transponder, SC/UPC Connector,

PH1-NLASC2725 Parametric

Parameter NameAttribute value
Objectid1871067399
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsOC-192, SONET
Connection TypeSC/UPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1531 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Power supply monitoring
Has anyone used power supply power monitoring IC or solution? I found one, LTC2943, but I have never used it. I wonder if anyone has used this IC and how to use it. Can anyone help me? Thank you. Atta...
曹伟1993 Power technology
Invisibility cloak may be available soon
Xinhua News Agency, Los Angeles, May 27 (Xinhua) -- Scientists from the United States and the United Kingdom have recently completed a study on the principles of visual stealth technology. Scientists ...
JasonYoo RF/Wirelessly
EMC Control of LPC1788
Hello everyone, I am using the EMC of LPC1788 to read and write Nor Flash, Nand Flash, EEPROM, etc. I am not very clear about the configuration of EMC, the delay on the datasheet, etc., and I don't kn...
烟波钓徒 MCU
Some experience and improvements in TI NDK application development
[i=s]This post was last edited by Baboerben on 2019-11-6 21:33[/i]Recently, I have been doing software development on TI's processors. The project requires network communication functions. However, ne...
灞波儿奔 Microcontroller MCU
ADC Calibration
Question: What method do you use to calibrate the ADC? Can you post a program for reference? Thank you very much! !...
ailikelhl Microcontroller MCU
WINCE Control Panel does not see "Memory Management"
I want to ask if your WINCE5.0 system has a "memory management" control panel. I saw on the Internet that everyone seems to have it, but I can't see it in my Chinese kernel or English kernel. What's t...
xianghonghe Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1241  165  603  2899  1500  25  4  13  59  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号