WBDDQSC-B-01-2003-J-B datasheet, PDF

WBDDQSC-B-01-2003-J-B: DescriptionArray/Network Resistor, Bussed, 0.05W, 200000ohm, 100V, 5% +/-Tol, -100,100ppm/Cel, 1109,; CategoryPassive components The resistor; File Size273KB，4 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

WBDDQSC-B-01-2003-J-B Overview

Array/Network Resistor, Bussed, 0.05W, 200000ohm, 100V, 5% +/-Tol, -100,100ppm/Cel, 1109,

Parameter Name	Attribute value
Objectid	803090496
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Bussed
Number of terminals	24
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	0.406 mm
Package length	2.921 mm
Package form	SMT
Package width	2.184 mm
method of packing	Tray
Rated power dissipation(P)	0.05 W
resistance	200000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC-NETWORK
size code	1109
Temperature Coefficient	100 ppm/°C
Tolerance	5%
Operating Voltage	100 V

Wire Bondable

Resistor Network Arrays

Chip Network Array Series

Absolute tolerances to ±0.1%

Tight TCR tracking to ±5ppm/°C

Ratio match tolerances to ±0.05%

Ultra-stable tantalum nitride resistors

IRC’s TaNSil

network array resistors are ideally suited for applications that demand a small footprint. The small wire

bondable chip package provides higher component density, lower resistor cost and high reliability.

The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking and low cost.

Excellent performance in harsh, humid environments is a trademark of IRC’s self-passivating TaNSil

resistor film.

For applications requiring high performance resistor networks in a low cost, wire bondable package, specify IRC

network array die.





General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

10. 11

2008-10-18, Invitation to TI C64x Network Development and Application Technology Seminar: [align=center][align=center][b][font=宋体][size=15pt]——AKA Technical Salon: DSP[/size][/font][/b][/align][/align][align=center][align=center][font=Verdana][size=10.5pt] [/size][/font][/align][/align][fo...; dylhz RF/Wirelessly

[Wiring] Handling of ground via errors on hot air pads (suitable for obsessive-compulsive disorder): Author: Eric [color=#444444][backcolor=rgb(255, 255, 255)][font=Tahoma, Helvetica, SimSun, sans-serif][size=14px]For some LDO or chips, many have a hot air pad. In order to dissipate heat, ground vias...; ohahaha PCB Design

CP2102 schematic diagram: Help with cp2102n related circuits...; begin权丿 PCB Design

Infineon Position2Go Development Kit Review @3. Testing: After so much preparation, the most important test chapter is finally here. Based on the previous article, open the radar gui and the following picture will appear. You can modify the parameters throu...; landeng1986 Special Edition for Assessment Centres

MSP430 minimum system data: This minimum system board was purchased from Taobao for the purpose of developing a heat meter. Before welding:After welding:MSP430F149 minimum system schematic and user manual:...; xubifei2008 Microcontroller MCU

Problems with nb0 and nb1: I recently used wince5.0 to compile the kernel and found that in some cases, .nb1 files would be generated, such as eboot.nb1. In this case, I read some opinions that the space of eboot.nb0 is not eno...; weishutian Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components