EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

P1505Y2182BGTC

Description
Fixed Resistor, Thin Film, 0.35W, 21800ohm, 200V, 0.1% +/-Tol, 10ppm/Cel, Surface Mount, 1505, CHIP
CategoryPassive components    The resistor   
File Size143KB,10 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

P1505Y2182BGTC Overview

Fixed Resistor, Thin Film, 0.35W, 21800ohm, 200V, 0.1% +/-Tol, 10ppm/Cel, Surface Mount, 1505, CHIP

P1505Y2182BGTC Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid283793654
package instructionCHIP
Reach Compliance Codecompliant
Country Of OriginFrance
ECCN codeEAR99
YTEOL7.45
Other featuresANTI-SULFUR, HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.81 mm
Package formSMT
Package width1.32 mm
method of packingTR, PLASTIC
Rated power dissipation(P)0.35 W
Rated temperature70 °C
resistance21800 Ω
Resistor typeFIXED RESISTOR
size code1505
surface mountYES
technologyTHIN FILM
Temperature Coefficient10 ppm/°C
Terminal surfaceGOLD OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage200 V
Help: Problems encountered during program burning
I use MSPFET software to burn the program into the 1611 chip, and set it to BSL format. Why does it always show synchronization error when running? The LED flashes twice and then stops working....
zhaojiang1 Microcontroller MCU
Software filtering methods and procedures
[i=s] This post was last edited by paulhyde on 2014-9-15 03:03 [/i] 10 software filtering methods, and the corresponding program source code~~ Very useful~...
xianghong123 Electronics Design Contest
About enc28j60 network cable plug and unplug problem
The control chip is STC12C5A60S2, the communication module uses enc28j60, and the transplanted uip protocol stack. After the network cable is plugged in, it can be pinged, and the network debugging as...
feibao1988 MCU
How to connect flame sensor to microcontroller?
How to connect flame sensor to microcontroller? ? ? Circuit diagram, urgently needed, help...
←¢Royal★ MCU
5G millimeter wave radio frequency technology
[size=4] Hybrid beamforming, such as shown in the figure, will be the preferred architecture for 5G systems operating at microwave and millimeter wave frequencies. This architecture uses a combination...
Aguilera RF/Wirelessly
Help with the logic of gal16v8
Experts, I used gal16v8 to draw a schematic diagram to make a logic these days. In the middle, I used the output of a DF trigger as an intermediate variable. Why did the compiler say Cannot assign out...
laoniushiniu Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1973  2056  957  1737  1485  40  42  20  35  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号