EEWORLDEEWORLDEEWORLD

Part Number

Search

177-714-2-15GP4K5-24MNG

Description
Interconnection Device
CategoryThe connector    The connector   
File Size436KB,4 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-714-2-15GP4K5-24MNG Overview

Interconnection Device

177-714-2-15GP4K5-24MNG Parametric

Parameter NameAttribute value
Reach Compliance Codecompli
Connector typeINTERCONNECTION DEVICE
Base Number Matches1
MWDM Micro-D Shielded Cable Assemblies
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly
labor. 100% tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair
177-740 cables are furnished with a full complement of
white/blue twisted pair wires.
Integral Shield Termination–The
connector shell has a
platform to accept Band-It shield termination bands. The
cable shield braid is attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding with
Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully
shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector
shell and secured with a stainless steel
BAND-IT
® clamp. These pre-wired, 100% tested assemblies meet the
requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.
Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either
single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
– A gold-plated
stainless steel ground spring on the pin connector mating face offers
substantial improvement in EMI protection. The graphs compare
identical connectors tested with and without ground springs.
EMI Performance with Ground Spring
SHIELDING EFFECTIVENESS (DB)
SHIELDING EFFECTIVENESS (DB)
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
EMI Performance without Ground Spring
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
FREQUENCY (Hz)
FREQUENCY (Hz)
© 2006 Glenair, Inc.
CAGE Code 06324/0CA77
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
B-8
E-Mail: sales@glenair.com
TI Industrial Robots Online Seminar Resource Sharing
Main Agenda of the Seminar 1. Provide a detailed introduction to the definition and classification, system considerations, and module analysis of industrial robots; 2. Count the challenges faced in in...
arui1999 Robotics Development
【Signal processing】:FPGA implements DSP (digital signal processing technology)
[[i]This post was last edited by liuceone on 2011-12-10 17:30[/i]]...
liuceone FPGA/CPLD
I need help from forum friends to confirm whether the LCD12864 LCD serial driver using the ST7920 controller can read back the display data?
I have been using the LaunchPad G2553 board to write the LCD12864 display driver in 8-bit parallel mode. Now the functions are almost sufficient, so I want to expand some functions, but I find that th...
bobde163 Microcontroller MCU
Can small and medium-sized chips (40, 74, etc.) be controlled by VCC and GND? If VCC and GND are not added, will the circuit be affected if other pins are added to the circuit?
I want to use serial control for some chips. Can I use vcc and gnd to control them? The signal lines are connected in parallel. I use vcc and gnd to control whether they are connected or not. I think ...
SPEED Embedded System
[Sharing] First experience using iTOP-4412 development board [multiple pictures]
[align=left]I recently bought a 4412 development board, equipped with a 7-inch screen, WIFI module, and GPS module. Here are some photos to introduce it. The photo taken by the mobile phone is a bit b...
Chihiro Linux and Android
Create your own QR code on PCB
[i=s]This post was last edited by huaiqiao on 2016-5-23 19:03[/i] [size=3]1. First of all, I replied to a post two days ago about how to add a logo to a PCB. (See the reply on the 4th floor for detail...
huaiqiao PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 115  237  72  1087  1201  3  5  2  22  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号