EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11613206BBLF

Description
Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11613206BBLF Overview

Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-11613206BBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid307926122
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
body length9.45 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typePRESS FIT
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
I can't understand the circuit diagram at all
Is there any expert who can give me some advice? I can only understand simple circuit diagrams with few lines, and I can't understand complex circuit diagrams with many lines at all. Where should I st...
电子工程师小达 Analog electronics
Share some issues in debugging TMS320C2000 series?
[size=4]1) It can run in single step, but will always return to address 0 when running continuously: Watchdog is not turned off, and continuous running will reset the DSP back to address 0. [/size] [s...
Aguilera Microcontroller MCU
Several steps to effectively improve the quality of LED die bonding
有效提高LED固晶品质几大步骤  一、严格检测固晶站的LED原物料  1.芯片:主要表现为焊垫污染、芯片破损、芯片切割大小不一、芯片切割倾斜等。  预防措施:严格控制进料检验,发现问题要求供应商改善。  2.支架:主要表现为Θ尺寸与C尺寸偏差过大,支架变色生銹,支架变形等。  来料不良均属供应商的问题,应知会供应商改善和严格控制进料。  3.银胶:主要表现为银胶粘度不良,使用期限超过,储存条件和解...
探路者 LED Zone
Issues related to the USB chip CY7C68013.
I am a beginner in USB and would like to ask for advice on using the chip CY7C68013. Which of the two USB modes: GPIF and FIFO is better and easier to use? How should I handle the related pins? Thank ...
myseaweed Embedded System
Writing_Testbench
[color=rgb(0,0,0)][font=Times-Italic][size=14pt][i]Preface [/i][b][i]xvii[/i][/b] Why This Book Is Important What This Book Is About What Prior Knowledge You Should Have Reading Paths VHDL versus Veri...
白丁 FPGA/CPLD
Looking for arcade emulator FinalBurn for wince source code
I have been looking for a long time but I can't find it...
jumpbear Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 521  1664  1168  2614  1516  11  34  24  53  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号