EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

P1206H1213FBPD

Description
Fixed Resistor, Thin Film, 0.33W, 121000ohm, 200V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size143KB,10 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

P1206H1213FBPD Overview

Fixed Resistor, Thin Film, 0.33W, 121000ohm, 200V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP

P1206H1213FBPD Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145044718788
package instructionCHIP
Reach Compliance Codeunknown
Country Of OriginFrance
ECCN codeEAR99
YTEOL7.65
Other featuresANTI-SULFUR, HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.06 mm
Package formSMT
Package width1.6 mm
method of packingTR, PAPER
Rated power dissipation(P)0.33 W
Rated temperature70 °C
resistance121000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTIN LEAD SILVER OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage200 V
Asking for advice: smclk of msp430afe253
Has anyone used the msp430afe253 microcontroller? When I used this microcontroller, I measured the output of smclk and it was always high. I used the routine provided by TI and it was still high. Has ...
绵里针 Microcontroller MCU
Microcontroller Application Programming (Book)
Microcontroller Application Programming Design (Book), Super Star Reading Format http://www.dykf.com/Soft/ShowSoftDown.asp?UrlID=1SoftID=104...
fighting MCU
High speed ADC chip, who has any recommendations?
I saw a CS5510/11/12/13 in Cirrus Logic, but the PDF says that an external op amp is required. I don't want to add any extra external circuits. Has anyone done a similar project? The AD output rate ne...
slevin Embedded System
Help, multisim simulation always fails
I want to use multisim10.0 to simulate a circuit related to a potentiometer. However, when the potentiometer is set to 100%, the error shown in the picture will appear. I really don't know where the p...
sizumiyazhao Integrated technical exchanges
Why does this prompt appear when burning code with Keil?
Target dll has been canceled Debugger aborted...
zldzjzldh Embedded System
UF2 bootloader for ESP32-S2
The UF2 bootloader of ESP32-S2 has now been merged into tinyuf2 . It is mainly aimed at MCUs using TinyUSB , and currently supports ESP32-S2, iMXRT10xx, LPC55xx, and STM32F4. Using the UF2 bootloader,...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 656  2139  1891  2755  1119  14  44  39  56  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号