PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE MODULAR JACKS
1.0 SCOPE
This Product Specification covers the 1.02 mm (.040 inch) centerline (pitch) printed circuit board
(PCB) modular jack connector series with selective gold and tin plating.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER(S)
Single Port Inverted Modular Jack
Single Port Inverted Mini-PCI Modular Jack
Dual Port Inverted Modular Jack
Ganged Inverted Modular Jack
Single Port Inverted Modular Jack with Keep-out Feature
43860
44380
43814
44248
44620
2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS
See the appropriate sales drawings (SD-43860-001, SD-44380-001, SD-43814-001,
SD-44248-001) for information on dimensions, materials, plating and markings.
2.3 SAFETY AGENCY APPROVALS
UL File Number
. E107635
CSA File Number
.. LR19980
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
FCC Rules and Regulations, Part 68, Subpart F
REA Bulletin 345-81, PE-76; Specification for modular telephone set hardware
ANSI/EIA/TIA-568
IEC-60603-7
UL 1863
MIL-STD-202; General requirements for test specifications
4.0 RATINGS
4.1 VOLTAGE
56.5 V DC
150 V
RMS
AC (Ringing voltage only)
4.2 CURRENT
1.5 Amps @ 25°C
4.3 TEMPERATURE
Operating:
- 40°C to + 85°C
Nonoperating:* - 40°C to + 85°C
*Packaging materials should not exceed + 50°C
REVISION:
ECR/ECN INFORMATION:
EC No:
UCP2012-3129
DATE:
TITLE:
H3
2012/03/22
PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE
MODULAR JACKS
CHECKED BY:
SHEET No.
1
of
5
APPROVED BY:
DOCUMENT NUMBER:
CREATED / REVISED BY:
PS-43860-003
NNGUYEN
JBELL
FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.0 PERFORMANCE
5.1 ELECTRICAL REQUIREMENTS
DESCRIPTION
Contact
Resistance
(Low Level)
Insulation
Resistance
TEST CONDITION
Mate connectors: apply a maximum voltage
of
20
mV and a current of
100
mA.
(Measurement locations in Section 7.0)
Unmated connector, mounted to a PCB:
apply a voltage of
100
VDC between
adjacent terminals and between terminals to
ground.
Mate connectors: apply a voltage of
1000
VAC for
1
minute between adjacent
terminals and
1500
VAC between terminals
to shield.
REQUIREMENT
20
milliohms
MAXIMUM
[initial]
500
Megohms
MINIMUM
Dielectric
Withstanding
Voltage
No breakdown;
current leakage <
5
mA
REVISION:
ECR/ECN INFORMATION:
EC No:
UCP2012-3129
DATE:
TITLE:
H3
2012/03/22
PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE
MODULAR JACKS
CHECKED BY:
SHEET No.
2
of
5
APPROVED BY:
DOCUMENT NUMBER:
CREATED / REVISED BY:
PS-43860-003
NNGUYEN
JBELL
FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.2 MECHANICAL REQUIREMENTS
DESCRIPTION
Connector Mate
Force
TEST CONDITION
Mate connector at a rate of
25 ± 6
mm (1
± ¼
inch) per minute.
(Gage dimensions in Section 7.0)
Mate connectors up to
500
cycles at a
maximum rate of
10
cycles per minute prior
to Environmental Tests.
Amplitude: 1.50mm (.060”) peak to peak
Sweep: 10-55-10 Hz in one minute
Duration: 15 minutes
±X,±Y,±Z
axis (45 minutes total)
Apply an axial pullout force on the plug at a
rate of
25 ± 6
mm (1
± ¼
inch) per minute.
REQUIREMENT
22
N (5 lbf) unshielded
MAXIMUM insertion force
35
N (8 lbf) shielded
MAXIMUM insertion force
10
milliohms MAXIMUM
(change from initial)
10
milliohms MAXIMUM
(change from initial)
&
Discontinuity <
1
microsecond
89
N (20 lbf)
MINIMUM retention force
4.5
N (1 lbf)
MINIMUM withdrawal force
before solder reflow
89
N (20 lbf)
MINIMUM withdrawal force
after solder reflow
10
milliohms MAXIMUM
(change from initial)
&
Discontinuity <
1
microsecond
Durability
Vibration
(Random)
Plug Retention
Force
PCB
Separation Forces
Apply a perpendicular load on the plug at a
rate of
25 ± 6
mm (1
± ¼
inch) per minute.
Shock
(Mechanical)
Mate connectors and shock at
50
g’s with
three saw tooth wave form shocks in the
±X,±Y,±Z
axis (18 shocks total).
REVISION:
ECR/ECN INFORMATION:
EC No:
UCP2012-3129
DATE:
TITLE:
H3
2012/03/22
PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE
MODULAR JACKS
CHECKED BY:
SHEET No.
3
of
5
APPROVED BY:
DOCUMENT NUMBER:
CREATED / REVISED BY:
PS-43860-003
NNGUYEN
JBELL
FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.3 ENVIRONMENTAL REQUIREMENTS
DESCRIPTION
Shock
(Thermal)
TEST CONDITION
Mate connectors; expose to
10
cycles of:
-40°C
to +85°C
30
minutes dwell
REQUIREMENT
10
milliohms MAXIMUM
(change from initial)
&
Visual: No Damage
10
milliohms MAXIMUM
(change from initial)
&
Visual: No Damage
10
milliohms MAXIMUM
(change from initial)
&
Dielectric Withstanding
Voltage:
No Breakdown at
500
VAC
&
Insulation Resistance:
200
Megohms MINIMUM
&
Visual: No Damage
Thermal Aging
Mate connectors; expose to:
240
hours at
85±2°C
±
Humidity
(Cyclic)
Mate connectors: expose to
10
cycles at
90-95%
relative humidity with
temperatures at +25°C and +65°C per
MIL-STD-202F method 106F
(without -10°C dip)
Dip connector terminal tails in solder:
Solder Duration:
7±0.5
seconds
±
Solder Temperature:
260±5°C
±
{Recommended
same parameters as
SMES-152.}
Note: The solder resistance test simulates a
wave solder process. This test should not be
used to determine the suitability of the
connector for a convection or IR reflow solder
process.
Visual:
No Damage to insulator
material
Solder
Resistance
REVISION:
ECR/ECN INFORMATION:
EC No:
UCP2012-3129
DATE:
TITLE:
H3
2012/03/22
PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE
MODULAR JACKS
CHECKED BY:
SHEET No.
4
of
5
APPROVED BY:
DOCUMENT NUMBER:
CREATED / REVISED BY:
PS-43860-003
NNGUYEN
JBELL
FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
6.0 PACKAGING
Parts shall be packaged to protect against damage during handling, transit and storage.
See appropriate sales drawings on Sheet 1 for packaging descriptions.
7.0 GAGES AND FIXTURES
TERMINATION RESISTANCE MEASUREMENT POINTS
Connector and plug terminals and wire conductor bulk
resistance to be subtracted from measurements
8.0 OTHER INFORMATION
REVISION:
ECR/ECN INFORMATION:
EC No:
UCP2012-3129
DATE:
TITLE:
H3
2012/03/22
PRODUCT SPECIFICATION
INVERTED RIGHT ANGLE
MODULAR JACKS
CHECKED BY:
SHEET No.
5
of
5
APPROVED BY:
DOCUMENT NUMBER:
CREATED / REVISED BY:
PS-43860-003
NNGUYEN
JBELL
FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
京公网安备 11010802033920号
EEWORLD
