FMXMC3S2118DFE-10.000000M-TR datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMC3S2118DFE-10.000000M-TR

FMXMC3S2118DFE-10.000000M-TR: DescriptionParallel - Fundamental Quartz Crystal, 10MHz Nom, SMD, 2 PIN; CategoryPassive components Crystal/resonator; File Size338KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMC3S2118DFE-10.000000M-TR Overview

Parallel - Fundamental Quartz Crystal, 10MHz Nom, SMD, 2 PIN

FMXMC3S2118DFE-10.000000M-TR Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1312670023
package instruction	SMD, 2 PIN
Reach Compliance Code	compliant
Other features	TR
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	10 µW
frequency stability	0.002%
frequency tolerance	10 ppm
load capacitance	18 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	10 MHz
Maximum operating temperature	60 °C
Minimum operating temperature	-10 °C
physical size	5mm X 3.2mm X0.9mm
Series resistance	100 Ω
surface mount	YES

Preview

Download Datasheet

View All

FMXMC3S2

SERIES

Microprocessor Crystals

Surface Mount Ceramic Pkg.

Micro 5 x 3.2, 2-Pad / Ultra Thin

High Reliability

Tight Stability

Actual Size

CERAMIC SMD 5x3.2

SPECIFICATIONS

Issue 3 - 08212015

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

Insulation Resistance

Reflow Conditions

All specifications subject to change without notice.

Specification

8.00 - 150.00 MHz

See Operation Mode and ESR Table

18 pF Std., 6 - 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-40 to +85°C / -55 to +125°C

See Operation Mode and ESR Table

7 pF max.

10 µW typical, 300 µW max

±5 ppm per year max.

500MΩ min. at 100V

±15V

260°C ±10°C for 10sec max., 2 reflows max.

5 x 3.2 CERAMIC SMD

OPERATION MODE AND ESR TABLE

Frequency (MHz)

8.00 - 10.00

10.01 - 12.00

12.01 - 20.00

20.01 - 50.00

40.00 - 150.00

Mode

Fundamental

3rd Overtone

Max. ESR (Ohms)

100

STANDARD MARKING

XXX.XXXM

FMI YYWW

XXX.XXXM FREQUENCY in MHz

FMI, Date Code

Recommended Solder Pad Layout

NOTE: Standard Specifications for product indicated in

color

Dimensions: millimeters

PART DESCRIPTION SYSTEM

FMXM C3S2 1 18 H J A

XX.XXXXXXM

Product Family

MicroP Crystal

Package

Ceramic SMD

3.2x5 mm, 2 Pad

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

XX - Custom (pF)

Cal. Tol. @ 25°C

D ±10 ppm

E ±15 ppm

F ±20 ppm

H ±30 ppm

J ±50 ppm

K ±100 ppm

X Custom

Temp. Tol.

D ±10 ppm

E ±15 ppm

F ±20 ppm

H ±30 ppm

J ±50 ppm

K ±100 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

TR - Tape & Reel

PD - Parameter Data

TD - Temp. Data

CM- Custom Mark

BLANK - None Req’d.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

Use 555 to make DC-DC boost circuit

AD574A Unipolar and Bipolar Input Circuita

One of the thyristor voltage-regulated drying room temperature control circuits

555 acute coronary insufficiency alarm circuit

Electronic relay phase failure protection circuit

Basic knowledge and drivers of standard and white LEDs (2)

LINUX makefile problem!!!!: CC = ckcore-elf-gcc AS = ckcore-elf-as LD = ckcore-elf-ldCFLAGS= -mbig-endian-c -O2 -g ASFLAGS = -mbig-endianOBJECT = tinyloader.o tiny_spi.o tiny_main.o vectors.o \main.o pll_config.o tinyloader2.o\c...; flywing Linux and Android

2410 DMA memory copy, how to set registers: I want to copy 2M data starting from memory address Addr1 to Addr2. How can I use DMA to achieve this?...; atao9527 Embedded System

Image Processing Based on FPGA: ...; 至芯科技FPGA大牛 FPGA/CPLD

How to use XBYTE to read and write DS12B887: The 51 MCU and DS12B8 are connected in bus mode, where the CS chip select segment is connected to Y0 of the decoder 74HC154, and the address lines A\B\C\D of 74HC154 are connected to P2_3, P2_4, P2_5,...; 38824520 Embedded System

Explanation of op amp parameters and selection of commonly used op amps: [i=s]This post was last edited by qwqwqw2088 on 2015-9-11 09:20[/i] [align=left]Integrated op amps have many parameters, the main parameters are divided into DC indicators and AC indicators, and all c...; qwqwqw2088 Analogue and Mixed Signal

[Contribute to C2000] The principle of CCS and DSP_BIOS - routines: I think this information is good. Students who find it useful can collect it and don't forget to leave a footprint. I have a lot of information here, all of which I would like to share. Let's make pro...; fxw451 Microcontroller MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components