Original author: KVIN Reprint link: https://www.icxbk.com/article/detail?aid=969After completing SVPWM, you can determine your direction according to your project requirements, whether it is Hall FOC,...
There are 2 types of serial port modes (low frequency mode and oversampling mode). What is the difference between the two? The crystal oscillator is 32768. How to set the baud rate to 9600 using the o...
[align=left]No more words to say, read it yourself! :):Laugh::titter:[/align][align=left]Energia official website address: [url=http://energia.nu/]http://energia.nu/[/url][/align] [align=left]Energia ...
There are two main ways, one is to use the matlab filter toolbox to design and generate Verilog or VHDL code, the other is to use the matlab filter toolbox to design and export coefficients, and then ...
[b][size=5][color=#0000ff][backcolor=rgb(245, 248, 253)][font=simsun]The article reproduced below is from a foreign website a few years ago. For many power supply beginners, this article is still very...
1. After selecting PH in the webench initial test interface, enter the interface as follows to select the sensor2. LMP91200 is a chip specially designed for measuring PH by TI, as shown below3. You ca...
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
1 Introduction to the overall system solution
The hardware part is mainly used to amplify the sound. When the sound is loud enough, the signal can be introduced into the microcontroller for de...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
