Because I participated in the evaluation of the GW1N FPGA, the plan at that time was to use GW1N to collect data from the 24-bit ADC LTC2380-24 and then analyze it, but I don't know where the LTC2380-...
[font=微软雅黑] I want to change my phone recently. I have a habit of disassembling my old phone to see the internal structure and then putting it back together to give it to someone else or use it as a s...
The three-phase power supply phase sequence/phase loss detector introduced in this article is mainly used to detect whether the wiring of the three-phase AC power supply is missing a phase and whether...
Use F149 to drive relays and drive 380V three-phase motors.Use two-pole relays.Use optocouplers in the middle to drive the first-stage relay.The first-stage relay controls the second-stage 380 relay.W...
Assume that the DAC uses an inverting operational amplifier, C1=C2, A(0)=1000, and VREF=1V. What is the maximum accuracy of the DAC under the worst-case scenario? The loop gain of the inverting amplif...
On April 24, Sungrow released its annual financial report. The report shows that in 2017, Sungrow's global shipments reached 16.5GW, of which domestic shipments reached 13.2GW, a year-on-year incre...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
This program mainly uses the comparison output function of the timer to generate PWM waves to control the LED. The comparison output of timer A corresponds to P2.3 P2.4. Therefore, a matching working...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
1. Brief description A summary of "How to build uClinux kernel transplantation on ARMSYS development board with S3C44B0X as core", including the analysis of Bootloader function and the key co...[Details]
In 1949, after three years of civil war, the Nationalist government was defeated and retreated to Taiwan. The political and academic circles launched a large-scale reflection on why they failed in ...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
Ouster LiDAR OS-1 (left) and OS-2 (center) Velodyne invented the modern 3D LiDAR scanner in the mid-2000s, but in recent years conventional wisdom has held that Velodyne’s design — 64 lasers mounted...[Details]
The code for using timer 0 to implement a running light in a 51 MCU is as follows. The LED light is connected to port P1. The code is annotated below, so I won't explain it in detail. My English is n...[Details]
Table of contents: 1 Overview 2: Common interrupt functions 3: PWM output 1 Overview In development, timers are widely used, which can be simply summarized into three aspects: 1.1: Application of ...[Details]
The single-chip microcomputer running light program requires all 32 serial ports to be used, and each serial port has eight LEDs. Question supplement: The 8051 single-chip microcomputer is used, an...[Details]
A simple experimental programming question for the microcontroller: write a 3-byte binary addition subroutine. The program entry is: addend 1: 22H, 21H, 20H three bytes, 22H is the highest bit; adden...[Details]
1. Pin: 0 in 1 out Set Status Output status IO register setting DDR×A certain bit is set to 1, and the corresponding bit IO is set to output; PORT×A certain position is 1/0, and t...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
