EEWORLDEEWORLDEEWORLD

Part Number

Search

3MS-WDP7-P2-B1-M71GE

Description
Pushbutton Switch, DPDT, Latched And Momentary, 1A, 28VDC, Solder Terminal, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size2MB,11 Pages
ManufacturerCarling Technologies
Environmental Compliance
Download Datasheet Parametric View All

3MS-WDP7-P2-B1-M71GE Overview

Pushbutton Switch, DPDT, Latched And Momentary, 1A, 28VDC, Solder Terminal, Through Hole-right Angle

3MS-WDP7-P2-B1-M71GE Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerCarling Technologies
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typePLUNGER
Other featuresPANEL MOUNTABLE
body width11.4 mm
body height12.7 mm
Body length or diameter12.7 mm
Contact (AC) maximum rated R load1A@120VAC
Maximum contact current (AC)1 A
Maximum contact current (DC)1 A
Contact (DC) maximum rated R load1A@28VDC
Maximum contact voltage (AC)120 V
Maximum contact voltage (DC)28 V
Electrical life50000 Cycle(s)
JESD-609 codee4
Manufacturer's serial number3MS
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
sealEPOXY TERMINAL SEALED; IP68
surface mountNO
Switch actionLATCHED AND MOMENTARY
switch functionDPDT
Switch typePUSHBUTTON SWITCH
Terminal surfaceGold (Au)
Termination typeSOLDER
Base Number Matches1
Carling
Technologies
3M-Series Miniature Pushbutton Switches
3MN-Series
Snap-Action
Miniature
Pushbutton Switch
Specifications
Contact Rating . . . . . . . . . refer to ordering scheme
Electrical Life . . . . . . . . . . 50,000 make & break cycles @ full
load
Contact Resistance. . . . . .
3MN& 3MA-Series:
10 mΩ max. ini-
tial @ 2-4 VDC 100mA for both sil-
ver & gold plated contacts.
3MS-Series:
50 mΩ max. initial @
2-4 VDC 100mA for both silver &
gold plated contacts.
Insulation Resistance . . . 1000 MΩ min.
Dielectric Strength . . . . . . 1500 Volts RMS @ sea level
Operating Temperature . . . -30°C to +85°C
Index of Protection . . . . . .
3MS -Series:
IP68
Cap Installation Support . .
3MS-Series:
10 lbs. max.
Solder Heat Resistance. . . MIL-STD-202, Method 210
Actuator Travel . . . . . . . . . 25°
3MS-Series
Sealed Snap-Action
Miniature Pushbutton
Switch
Materials
Case . . . . . . . . . . . . . . . .
3MN & 3MA-Series:
Dially phthalate
(DAP) (UL 94V-0)
3MS-Series:
Glass filled nylon 6/6,
flame retardant, heat stabilized (UL
94V-0)
Plunger. . . . . . . . . . . . . . .3MN-Series: Thermoplastic poly-
ester, black
3MS & 3MA-Series:
Glass filled
nylon or glass filled polyester (UL
94V-0)
Bushing . . . . . . . . . . . . . .
3MN-Series:
Brass, nickel plated
3MA-Series:
Zinc, nickel plated
Housing. . . . . . . . . . . . . . .3MN
& 3MA-Series:
Stainless Steel
Switch Support Retainer . .3MS-Series: Stainless Steel
Terminal Seal . . . . . . . . . . Epoxy
3MA-Series
Alternate
Action
Miniature Pushbutton
Switch
3M-Series Optional Cap
To order a cap assembled on a switch, specify the switch number followed by the cap part number and the word “assembled”.
Ex: 3MN-SP-7-P2-B6-M6QE-C13ASSEMBLED
To order caps in bulk, specify the Series, followed by the cap. Ex.) 3MN-C13
3MN
-
C1 3
1
Series
2
Cap Size
3
Color
1 SERIES OR SWITCH CATALOG NUMBER
3MN, 3MS
or
3MA
2 CAP SIZE
C1
C2
C3
C4
round 7.6mm dia.
round 9.35 mm dia.
square 11.7 x 11.7mm
round 5mm dia.
C5
C6
round 14.5mm dia.
(for 3MA w/ PL bushing)
brass chrome plated
(for 3MA w/ PD bushing)
3 CAP COLOR
1
2
3
4
1
white
black
red
orange
5
6
7
yellow
green
blue
Black, white & red standard. Other colors available. Consult factory.
www.carlingtech.com
35
How to set unused pins in Quartus II
Dear experts, how should I set the unused pins in Quartus II? The default setting in the software is As output driving ground, but the Internet says that this setting will cause the chip to heat up. G...
沉默珏殇 FPGA/CPLD
Xunwei-i.MX6 development board manual update-non-device tree uboot-modify default environment variables
This document mainly introduces how to modify the default boot parameters of non-device tree uboot. After the iTOP-iMX6 development board is burned, the default is the system parameters and screen par...
遥寄山川 ARM Technology
Problems encountered when using CH375 to communicate with PC in device mode.
I used DEBUG372.EXE (downloaded debugging tool) on the host computer. I uploaded several numbers to endpoint 1 and endpoint 2, and they were normal. When I downloaded to endpoint 2, the "number of dat...
ykfall Embedded System
How to solve the signal fluctuation from the sensor?
The signal from the sensor is very weak, and the circuit behind it has been amplified and filtered. When the detection quantity remains unchanged, the amplified signal has certain fluctuations. Lookin...
sfcsdc Analog electronics
AD Software
Can Altium Design software simulate? That is, the components have actual input and output, rather than just drawing schematics and then onto the PCB board....
如此美好 PCB Design
Problems in using LMT01 temperature measurement
I have recently been using the temperature measuring element LMT01 produced by TI. I chose your TI product based on its own measurement range and low power consumption. According to the official data ...
zb495203317 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1423  1633  1605  2187  1942  29  33  45  40  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号