8N4Q001KG-0001CDI8 datasheet, PDF

Datasheet> All Categories > semiconductor> Analog mixed-signal IC> 8N4Q001KG-0001CDI8

8N4Q001KG-0001CDI8: DescriptionIC osc clock QD freq 10clcc; Categorysemiconductor Analog mixed-signal IC; File Size163KB，20 Pages; ManufacturerIDT (Integrated Device Technology, Inc.); Websitehttp://www.idt.com/

Download Datasheet Parametric View All

8N4Q001KG-0001CDI8 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	8N4Q001KG-0001CDI8	-	-	View	Buy Now

8N4Q001KG-0001CDI8 Overview

IC osc clock QD freq 10clcc

8N4Q001KG-0001CDI8 Parametric

Parameter Name	Attribute value
Datasheets
IDT8N4Q001 Rev G
FemtoClock®
NG Ordering Guide
Standard Package	1,000
Category	Integrated Circuits (ICs)
Family	Clock/Timing - Programmable Timers and Oscillators
Packaging	Tape & Reel (TR)
Type	Clock Oscill
Cou	-
Frequency	125MHz, 100MHz, 122.88MHz, 156.25MHz
Voltage - Supply	3.135 V ~ 3.465 V
Current - Supply	160mA
Operating Temperature	-40°C ~ 85°C
Package / Case	10-CLCC
Supplier Device Package	10-CLCC (7x5)
Mounting Type	Surface Mou
Other Names	IDT8N4Q001KG-0001CDI8IDT8N4Q001KG-0001CDI8-ND

Preview

Download Datasheet

View All

Quad-Frequency Programmable XO IDT8N4Q001 REV G

DATA SHEET

General Description

The IDT8N4Q001 is a Quad-Frequency Programmable Clock

Oscillator with very flexible frequency programming capabilities. The

device uses IDT’s fourth generation FemtoClock® NG technology for

an optimum high clock frequency and low phase noise performance.

The device accepts 2.5V or 3.3V supply and is packaged in a small,

lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.

Besides the four default power-up frequencies set by the FSEL0 and

FSEL1 pins, the IDT8N4Q001 can be programmed via the I

interface to output clock frequencies between 15.476MHz to

866.67MHz and from 975MHz to 1,300MHz to a very high degree of

precision with a frequency step size of 435.9Hz ÷

(N is the PLL

output divider). Since the FSEL0 and FSEL1 pins are mapped to four

independent PLL divider registers (P, MINT, MFRAC and N),

reprogramming those registers to other frequencies under control of

FSEL0 and FSEL1 is supported. The extended temperature range

supports wireless infrastructure, telecommunication and networking

end equipment requirements.

Features

•

Fourth generation FemtoClock® NG technology

Programmable clock output frequency from 15.476MHz to

866.67MHz and from 975MHz to 1,300MHz

Four power-up default frequencies (see part number order

codes), re-programmable by I

C programming interface for the output clock frequency and

internal PLL control registers

Frequency programming resolution is 435.9Hz ÷N

One 2.5V, 3.3V LVDS clock output

Two control inputs for the power-up default frequency

LVCMOS/LVTTL compatible control inputs

RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps

(typical), integer PLL feedback configuration

RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps

(typical), integer PLL feedback configuration

Full 2.5V or 3.3V supply modes

-40°C to 85°C ambient operating temperature

Available in Lead-free (RoHS 6) package

Block Diagram

OSC

XTAL

÷MINT,

MFRAC

FSEL1

FSEL0

SCLK

SDATA

Pulldown

Pullup

Pin Assignment

÷P

PFD

LPF

FemtoClock® NG

VCO

1950-2600MHz

÷N

Q

DNU 1

OE 2

GND 3

FSEL0 4

FSEL1 5

10 SCLK

9 SDATA

8 V

7 nQ

6 Q

Configuration Register (ROM)

(Frequency, APR, Polarity)

C Control

IDT8N4Q001

10-lead ceramic 5mm x 7mm x 1.55mm

package body

CD Package

Top View

IDT8N4Q001GCD

REVISION A

MARCH 6, 2012

Recommended Resources

Dual power supply circuit

24-bit, 250kSPS single power supply data acquisition system

Maintenance circuit of high frequency electronic ballast

Micropower reference power supply

Circuit diagram of low temperature coefficient precision voltage regulator composed of CW136

Integrated regulated power supply with fixed negative output to protect the input from short-circuit when using large capacitive loads

Research on Fault Self-diagnosis of Electric Power Steering System: Abstract: Based on the introduction of the basic principles of fault self-diagnosis of electronic control systems, this paper proposes a fault diagnosis method based on the steering column electric po...; frozenviolet Automotive Electronics

Based on MSP430 Timer: ...; pontiff Microcontroller MCU

LPC2132: I made a LPC2132 board, and found that the LPC2132 does not work after powering it on. Because it cannot run programs that can be executed correctly on other LPC2132 boards. The power supply is 3.3V, ...; passion07 Embedded System

How to use the SD card module routine of MSP430f149?: [i=s]This post was last edited by DLHNR on 2015-7-18 14:55[/i] According to the program, a TXT file should be written to the SD card. But there is nothing in it. I checked and it is stuck at this step...; DLHNR Microcontroller MCU

Regarding the schematic diagram of the OMAP-L138 chip, please tell me: The company is going to use the OMAP-L138 chip for a board. We are using mentor to design the schematic. How do you get the chip library? It has 361 pins. Is there a pin list file like FPGA that can b...; kuayikua DSP and ARM Processors

Distinguishing between CDMA and GPRS: Hi, I want to use VC to write a program to determine whether the mobile phone is using CDMA or GPRS, and then establish a connection. How can I determine whether the mobile phone is using CDMA or GPRS...; pcwe Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components