XCTN26333001G datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> XCTN26333001G

XCTN26333001G: DescriptionRES NET,THIN FILM,33K OHMS,100WV,2% +/-TOL,-10,10PPM TC,0303 CASE; CategoryPassive components The resistor; File Size118KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

XCTN26333001G Overview

RES NET,THIN FILM,33K OHMS,100WV,2% +/-TOL,-10,10PPM TC,0303 CASE

XCTN26333001G Parametric

Parameter Name	Attribute value
package instruction	SMT, 0303
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Chip
Manufacturer's serial number	CTN
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	0.254 mm
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-STD-883
resistance	33000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	CTN
size code	0303
Temperature Coefficient	-10,10 ppm/°C
Tolerance	2%
Operating Voltage	100 V

Preview

Download Datasheet

View All

CTN

Vishay Electro-Films

Nichrome Thin Film, Center Tapped Resistors

CHIP

RESISTORS

FEATURES

•

Wire bondable

Product may not

be to scale

•

Center tap feature

•

Chip size: 0.030 inches square

•

Resistance range total: 10

to 1 MΩ

•

Ratio tolerances to: 0.1 %

•

Resistor material: Nichrome

•

Oxidized silicon substrate for good power dissipation

The CTN series is a center tapped nichrome resistor chip

providing excellent stability at 250 mW power levels. The

CTN offers the designer flexibility in use as either a single

value resistor or as two resistors with a center tap feature.

The CTNs six bonding pads allows the user increased layout

flexibility.

The CTNs are manufactured using Vishay Electro-Films

(EFI) sophisticated thin film equipment and manufacturing

technology. The CTNs are 100 % electrically tested and

visually inspected to MIL-STD-883.

APPLICATIONS

The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and

tracking between two resistors is critical.

Recommended for Hermetic environment where die is not exposed to moisture.

For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.

Vishay EFI measures low-value resistors by the four wire Kelvin technique.

TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES

Tightest Standard Tolerance Available

0.5 %

0.1 %

± 10 ppm/°C

± 25 ppm/°C

± 50 ppm/°C

± 100 ppm/°C

PROCESS CODE

CLASS H*

203

202

200

201

*MIL-PRF-38534 inspection criteria

1 MΩ

CLASS K*

263

262

260

261

100

200

1 kΩ

STANDARD ELECTRICAL SPECIFICATIONS

PARAMETER

TCR Tracking Between Halves (R

)

Center Tap Ratio,

Tolerance

Noise, MIL-STD-202, Method 308, 100

- 250 kΩ

Stability, 1000 h, + 125 °C, 125 mW

Operating Temperature Range

Dielectric Voltage Breakdown

Insulation Resistance

Operating Voltage

DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)

* 20 ppm/°C for

< 20

www.vishay.com

For technical questions, contact: efi@vishay.com

Document Number: 61024

Revision: 12-Mar-08

± 2 ppm/°C *

1 ± 1 % standard

- 35 dB typ.

± 0.1 %

ΔR/R

- 55 °C to + 125 °C

200 V

min.

100 V max.

250 mW

Recommended Resources

Some knowledge about electromagnetic compatibility laboratory in engineering design

Robot sound generator

Instantaneous water heater automatic constant temperature experimental circuit diagram

Complementary ramp signal generator circuit diagram

15V power supply circuit diagram with good filtering effect

Up and down slope relay control circuit diagram

Embedded development concept problem, please guide me: What is the concept of embedded system transplantation? Compared with the microcontroller we mentioned before, how is programming on the system different? If I need to learn VC, I only know C. What ab...; maosongbai Embedded System

Ten major electric control valve troubleshooting examples: [font=微软雅黑]Fault 1: The actuator does not move, but the power and signal lights of the control module are on. [/font][font=微软雅黑]Solution: Check whether the power supply voltage is correct; whether the...; yunrun Integrated technical exchanges

The AD value after downsampling is quite different from the original AD value. How to solve it?: Hello everyone, I'm working on a sliding average algorithm for ADC recently. I encountered a problem, please advise. Let's talk about the normal situation first. The steps to transmit ADC data to the ...; fengboning Embedded System

MPC8321 target board register file: Does anyone have the Vision Click simulator's MPC8321 target board register file? I need it urgently. Thanks....; emaster Embedded System

Application of Electronic Control Technology in Automobile Engines: 1. Introduction 1) Basic principles and structure of automobile engines The working process of automobile engines in the world today is basically composed of four strokes, namely intake, compression, ...; frozenviolet Automotive Electronics

There is a kind of feeling called invisible to it, and there is a kind of feeling called online to it.: Have beautiful eyes,Put it on someone's profile picture.Whether you are online or invisible,He can see you.That is an eye that can illuminate himself for a long time.It is the warmest decoration for s...; 8fu8 Talking

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components