EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8A-02-1962-B-B

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 19600ohm, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 2244, DIP
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GM8A-02-1962-B-B Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 19600ohm, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 2244, DIP

GUB-GM8A-02-1962-B-B Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1076313720
package instructionSMT, 2244
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL4.88
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor19600 Ω
JESD-609 codee0
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance19600 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeGULL WING
Tolerance0.1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
STC chip serial port 1 cannot transmit data using an independent baud rate generator.
[code]#include #includesfr AUXR = 0x8E; sfr AUXR1 = 0xA2; sfr BRT = 0x9C; //#define RELOAD_COUNT 0xFC //9600 //External crystal oscillator: 14.7456M void init_comm() { SCON=0x50; //Mode 1, 8-bit UART ...
qiaogang Embedded System
Internal Hardware Resources of PIC Microcontroller 16F84 (VIII)
12 How to use E2PROM   In the PIC16F84 microcontroller, in addition to the data memory composed of SRAM that can be directly addressed, there is also an E2PROM data memory that can be electrically era...
rain Microchip MCU
6410 decoding problem
Recently, I was working on the hardware codec of the 6410 development board, but it was not going well. I finally watched the DEMO and succeeded in the complete codec. As a result, I upgraded the BSP ...
AK4008 Embedded System
Angry! What is wrong with this world? People always bully the weak!
This afternoon, a Tencent news article popped up on my screen: "A man in Leizhou, Guangdong, broke into a school with a knife and injured 19 teachers and students." I was startled and quickly opened i...
向农 Talking
I want to DIY a bicycle taillight. Do you have any good suggestions?
I just bought a bicycle recently, but it doesn't have a taillight. I want to make one myself. Do you have any good suggestions? I just want it to be bright enough at night, simple and stable:lovelines...
libobozyy DIY/Open Source Hardware
I have read several MFRC522 packages on the Internet and have some doubts. Please give me some advice.
[i=s] This post was last edited by hanwenli123 on 2014-12-10 15:20 [/i]I found several versions of PCB footprints on the Internet. I don’t know which one is correct. I would like to ask a knowledgeabl...
hanwenli123 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2495  1688  2319  2562  982  51  34  47  52  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号