EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B210AUT0

Description
Fixed Resistor, Thin Film, 0.25W, 210ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B210AUT0 Overview

Fixed Resistor, Thin Film, 0.25W, 210ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP

D55342E07B210AUT0 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145080676981
package instructionCHIP
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.45
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance210 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn90Pb10) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Show the WEBENCH design process + solar cell voltage reduction circuit design with the lowest cost
Use WEBENCH to design the lowest cost circuit design for solar cell step-down. The total BOM cost is $1.21 and the efficiency is 92%. The overall situation is good. Finally, upload the entire design d...
hanskying666 Analogue and Mixed Signal
About low power consumption and watchdog
I use the MSP430F247 chip. The system is in LPM3 low-power mode most of the time, and occasionally wakes up through an external IO port interrupt. My watchdog clock uses an external 32768 crystal osci...
011fmh Microcontroller MCU
【Launchpad Experience】Note on the issues that need to be paid attention to when debugging the G2553 serial port of the Robam EXP430G2
When debugging the G2553 serial port of the ROBAM EXP430G2 (below 1.5, excluding 1.5), you should think about swapping the serial port's transmit and receive ports, that is, remove the TXRX route and ...
littleshrimp Microcontroller MCU
National MCU Development Engineer Salary Survey
National MCU development engineer salary survey, please reply in the following format: Highest education: Gender: Years of work experience: N years Years of experience in MCU development: N years Regi...
amu08 Embedded System
Wince printing problem
Hello everyone, please help me solve a problem. It is a WinCE printing problem: I use Visual Basic language in Visual Studio 2008 to develop WinCE, and now I need to implement the printing function. H...
SPEED Embedded System
[Transfer] How to learn to swim~~
Recently, I have been sensitive to the word "swimming". I saw it on Daicheng Space. There is a jingle for breaststroke coordination for HOHO. Before explaining the key points of breaststroke movements...
soso Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1145  497  291  670  1294  24  10  6  14  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号