EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272AC-0158CDI

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272AC-0158CDI Overview

LVDS Output Clock Oscillator

8N4S272AC-0158CDI Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308556819
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TRAY
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
Installation featuresSURFACE MOUNT
Nominal operating frequency166.62875 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
When using M4 LaunchPad for AD sampling, an error occurs once the sampling rate is configured?
I used M4 LaunchPad to configure AD. I read in the documentation that if I didn't configure it, the default would be 1MSPS. But when I called the SysCtlADCSpeedGet() library function, I found that the...
singletravel Microcontroller MCU
How to run Skype on WINCE? ? ?
I ran Skype on a WINCE5.0 PDA and it went wrong. I copied Skype1.2.exe, AYGSHELL.DLL, COREDLL.DLL, HTMLVIEW.DLL, and IPHLPAPI.DLL to the PDA, and then ran Skype1.2.exe. But it went wrong. I just want ...
cancan_919 Embedded System
How to process and restore the audio signal after FFT?
When processing an audio signal, I perform FFT after AD. After doing the corresponding processing in the frequency domain, I want to restore the audio signal, so I perform IFFT. I get a set of complex...
singletravel DSP and ARM Processors
[Domestic RISC-V Linux board Fang·Starlight VisionFive trial report] Nodejs development on Starlight board
In the official information, there is a special description of nodejs application:Nodejs is a very simple language that is easy to learn and use, because its core is JavaScript. Through the powerful n...
HonestQiao Domestic Chip Exchange
OLED Technology Consulting Part-time
Company Profile: We are a company in Shenzhen that does artificial intelligence in the industrial field. Currently, due to business reasons, we need to consult some industry and technical knowledge ab...
王铁成 Recruitment
Xiaobai: Matlab assisted DSP design FIR filter
Hello everyone, I read an article about matlab-assisted dsp design FIR. Using matlab's FDATool, you can design the filter and import the parameters into the CCS header file.However, the attached progr...
为爱一拼 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2917  1116  1136  918  1211  59  23  19  25  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号