Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
I just received an email from Tektronix about a " Energy Saving and Emission Reduction and Low Carbon Life Solutions Seminar " . I am struggling to solve the power supply harmonics problem! Great! I c...
[i=s] This post was last edited by paulhyde on 2014-9-15 03:44 [/i] Guo Tianxiang's full set of videos and routines for learning microcontrollers in ten days...
I found two-way pwm output on the Internet. The pins are PB6 and PB7. I want to expand it to four-way. How can I output from other pins? I always fail....
Because 8 I/Os are required, the reset pin of the MCU must be used as an I/O port. Verify the following operation method by reading the manual and the development board to make reset adjustments. [/si...
This multifunctional window has the following 5 functions: 1. Prevent harmful gas leakage: Automatically detect the concentration of harmful gases such as gas, smoke, alcohol, etc. in the room. When...
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
DCDC means DC to DC (conversion of different DC power values). Anything that meets this definition can be called a DCDC converter. Specifically, it means converting the input DC into AC through a s...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
This paper describes the design method of electronic multifunctional watt-hour meter, the key technology of hardware design and the software design process. Taking NEC's μPD78F0338 microcontroller ...[Details]
Preface
DS18B2 is generally used in conjunction with a single-chip microcomputer, and there are few reports on
the interface between
DSP
and DS18B20. Therefore, this article introdu...[Details]
introduction
Frequency characteristic tester
Also known as sweep frequency meter or frequency response analyzer, it uses a rectangular oscilloscope with internal scale as
a displ...[Details]
The embedded network module series products of Yingchuang Company all have a streamlined ISA expansion bus, which usually includes several address buses, 8-bit data buses, read and write control li...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
