EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8BLF-02-3881-C-B

Description
Array/Network Resistor, Bussed, Thin Film, 0.1W, 3880ohm, 0.25% +/-Tol, -50,50ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GL8BLF-02-3881-C-B Overview

Array/Network Resistor, Bussed, Thin Film, 0.1W, 3880ohm, 0.25% +/-Tol, -50,50ppm/Cel, 4430,

GUB-GL8BLF-02-3881-C-B Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795719759
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.1
structureMolded
JESD-609 codee3
Network TypeBussed
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.1 W
resistance3880 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance0.25%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
ARM&WINCE multi-channel data acquisition driver implementation ideas (seeking expert advice)
I want to write a driver for multi-channel data acquisition. The hardware uses S3C2410A, the operating system is wince, and the development tool is PB. This is my first time to come into contact with ...
天天雨 Embedded System
Basics of using software developed by LM3S8962
The forum is going to hold an event, so I'll upload some materials needed for beginners. Beginners can take a look at these two documents, which explain everything from installing the program, running...
wanghongyang Microcontroller MCU
About KernelIoControl
What is the difference between the first parameter of KernelIoControl, IOCTL_HAL_RELEASE_SYSINTR and IOCTL_HAL_REQUEST_SYSINTR: that is, what is the difference between KernelIoControl(IOCTL_HAL_RELEAS...
thinkz Embedded System
The block0img.nb0 generated by wince6.0 of s3c2451 cannot be used
I encountered this problem on wince6.0: blockimg0.nb0 compiled by s3c2450 in VS2005 cannot be used. Has anyone encountered such a problem? I suspect it is a problem with the settings in the .bib file,...
yangtao0123 Embedded System
How to understand header files in IAR
...
电子太 Microcontroller MCU
Experts please give me some advice
What is the difference between embedded and general software programming? Don't laugh at me for being a novice...
zserfv8210 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1068  42  1487  280  2285  22  1  30  6  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号