I would like to ask the experts: There are two ways to start the kernel in WINCE: bootloader (vivi) and eboot (built-in BSP). Now I want to upgrade from WINCE42 to wince50, but I don’t know much about...
[img]http://images22.51.com/6000/tf_digital/87d285dd879de62385f561622f9df420.jpg[/img] The circuit is drawn by myself, and my personal analysis is as follows. I hope you can correct me if there are an...
I would like to ask my friends. I have made a circuit with F1232 and downloaded and configured the program, but I don’t know how to measure the self-starting time of the chip. I hope everyone can help...
My son is over 2 years old, and he likes watching cartoons very much. But watching cartoons on mobile phones hurts the eyes, and watching TV is not pleasant either. If there is a projector, it would b...
State-of-The-Art in Efficient Linear PAsThere have been several techniques proposed to improve the average efficiency of linear PAs, and most notable are the dual PA (Doherty), envelope following, and...
After receiving the board, the first thing we planned to do was to build a compilation environment. The easiest way is to use the FC12 image in the CD. Then we need to build a virtual machine. 1. Choi...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
