EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

BLU2512-3921-FT101Q

Description
Fixed Resistor, Thin Film, 1W, 3920ohm, 200V, 1% +/-Tol, 100ppm/Cel, 2512,
CategoryPassive components    The resistor   
File Size345KB,1 Pages
ManufacturerRCD Components Inc.
Websitehttp://www.rcdcomponents.com/
Download Datasheet Parametric View All

BLU2512-3921-FT101Q Overview

Fixed Resistor, Thin Film, 1W, 3920ohm, 200V, 1% +/-Tol, 100ppm/Cel, 2512,

BLU2512-3921-FT101Q Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid739453396
Reach Compliance Codecompliant
Country Of OriginTaiwan
ECCN codeEAR99
YTEOL7.25
Other featuresULTRA PRECISION
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.61 mm
Package length6.3 mm
Package formSMT
Package width3.2 mm
method of packingTR
Rated power dissipation(P)1 W
Rated temperature70 °C
resistance3920 Ω
Resistor typeFIXED RESISTOR
size code2512
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage200 V
AM3359 ICE development board running powerlink on Linux
Hi, I have a TI AM3359 ICE development board. I have completed the Linux system porting. I want to run the Powerlink protocol on Linux. However, the network implementation of this board does not suppo...
simonls Linux and Android
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ask about the interrupt response speed
Hello everyone, I have been busy with the WM project recently and have not been online for a long time. I encountered a problem today and I would like to ask you for help. I hope you can give me some ...
huzhiming Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2002  923  1999  2346  2065  41  19  48  42  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号