Standard Frequencies – see Page 5 for common frequencies.
* Check with factory for availability of frequencies not listed.
Applications
IoT and IIoT Applications
Wireless Communications
FPGA/Microcontrollers
USB Interfaces
Computer Peripherals
Portable Equipment
Test and Measurement
M2M Communications
Broadband Access
Description
CTS Model 407 incorporates a high Q quartz resonator and is ideal for supporting a wide range of commercial and
industrial applications.
Ordering Information
Model
407
Mode of
Os ci l l a ti on
F
T ol era nce
@ +25°C
3
T em pera ture Sta bi l i ty/T em pera ture Ra ng e
5
Loa d
Ca pa ci ta nce
D
F requency
[ MHz ]
XXXMXXXX
Mode
Code
Fundamental
F
3rd Overtone
T
Code
- 20°C
1
X
2
3
5
Code
1
X
2
3
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
Stability Code
to +70°C - 30°C
±10ppm
R
±15ppm
Y
±20ppm
N
±30ppm
4
±50ppm
8
Stability Code
to +85°C - 40°C
±10ppm
-
±15ppm
W
±20ppm
6
±30ppm
7
±50ppm
9
Stability
to +85°C
-
±15ppm
±20ppm
±30ppm
±50ppm
Code
Frequency
Frequency
1
Code Capacitance Code Capacitance
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
16pF
Series
C
S
Notes:
1] Frequency is recorded with 3 leading digits before the "M" and 4 significant digits after the "M" [including zeroes]. (Ex. XXXMXXXX [016M3840],
There are frequencies with significant digits after the "M" that exceed the 4 digits. The remaining digits will be truncated from the CTS part
number, but the factory will calibrate to the full frequency desired. Examples below; P/N Frequency = Actual Frequency
13M5537 = 13.553750MHz
14M3181 = 14.318180MHz
16M6666 = 16.666670MHz
28M6363 = 28.636360MHz
N ot a l l perf orm a nce com bi na ti ons a nd f requenci es m a y be a va i l a bl e.
Conta ct your l oca l CT S Repres enta ti ve or CT S Cus tom er Servi ce f or a va i l a bi l i ty.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
I have seen many routines use BT as soft clock. If I detect the status of IO while doing soft clock, and LPM3_EXIT if certain conditions are met, will there be any problems? Please guide me:)...
After the program crashed, CeUnmountDBVol was not called. The next time the program was executed, CeMountDBVol (OPEN_ALLWAYS) failed. How can I solve this problem?...
Thank you for your attention and participation in this event. After checking everyone's weekly plan, we have selected the following 5 friends to participate in this M4 development board trial event. W...
As a hardware engineer, the most depressing thing is nothing more than this. You have worked hard to design a hardware circuit board, but you don’t have the copyright. You can’t do anything about it. ...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
