Standard Frequencies – see Page 5 for common frequencies.
* Check with factory for availability of frequencies not listed.
Applications
IoT and IIoT Applications
Wireless Communications
FPGA/Microcontrollers
USB Interfaces
Computer Peripherals
Portable Equipment
Test and Measurement
M2M Communications
Broadband Access
Description
CTS Model 407 incorporates a high Q quartz resonator and is ideal for supporting a wide range of commercial and
industrial applications.
Ordering Information
Model
407
Mode of
O s ci l l a ti on
F
Tol era nce
@ +25°C
3
Tem pera ture Sta bi l i ty/Tem pera ture Ra ng e
5
Loa d
Ca pa ci ta nce
D
F requency
[ MHz ]
XXXMXXXX
Mode
Code
Fundamental
F
3rd Overtone
T
Code
- 20°C
1
X
2
3
5
Code
1
X
2
3
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
Stability Code
to +70°C - 30°C
±10ppm
R
±15ppm
Y
±20ppm
N
±30ppm
4
±50ppm
8
Stability Code
to +85°C - 40°C
±10ppm
-
±15ppm
W
±20ppm
6
±30ppm
7
±50ppm
9
Stability
to +85°C
-
±15ppm
±20ppm
±30ppm
±50ppm
Code
Frequency
1
Frequency
Code Capacitance Code Capacitance
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
16pF
Series
C
S
Notes:
1] Frequency is recorded with 3 leading digits before the "M" and 4 significant digits after the "M" [including zeroes]. (Ex. XXXMXXXX [016M3840],
There are frequencies with significant digits after the "M" that exceed the 4 digits. The remaining digits will be truncated from the CTS part
number, but the factory will calibrate to the full frequency desired. Examples below; P/N Frequency = Actual Frequency
13M5537 = 13.553750MHz
14M3181 = 14.318180MHz
16M6666 = 16.666670MHz
28M6363 = 28.636360MHz
N ot a l l perf orm a nce com bi na ti ons a nd f requenci es m a y be a va i l a bl e.
Conta ct your l oca l CTS Repres enta ti ve or CTS Cus tom e r Servi ce f or a va i l a bi l i ty.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
Section 1: Mood and ClockTo be honest, I don't have many microcontrollers that I can use. I always think that any microcontroller can develop a good product.In the past few years, I used 51 and always...
There are two ways to add test points: 1. Leave a square pad of appropriate size, so that the test lead can directly touch it when testing, or solder a short piece of flying wire; 2. Leave a via. Ther...
I found a TFT-2.4 screen by accident. I saw that there are such screens on the market but they are very expensive. I want to make use of this screen, but I only found a PDF, and the introduction is a ...
[i=s]This post was last edited by dontium on 2015-1-23 11:37 [/i] How to minimize crosstalk in cable design [url]deyisupport./blog/b/analogwire/archive/2014/01/22/51614.aspx [/url] The best way to sol...
Software packages and components in Keil MDK development tool Version 5 : https://training.eeworld.com.cn/course/2206This tutorial video introduces the software packages and components in the ARM Keil...
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
introduction
The core features of mobile value-added service products are mobility, immediacy and personalization. Mobile value-added services are a new service mode that is rapidly developing...[Details]
1. Introduction
AS-Interface bus technology is an intelligent network that uses a single cable to connect sensors and actuators to controllers, transmit data, and provide power. It can be used...[Details]
Some people think: as long as the program runs well, it doesn't matter how the original program is written. But this is absolutely not the case. Software is not completed in one go, and it is neces...[Details]
I. Introduction
The use of electronics in cars dates back to the early 20th century when electric starters replaced hand cranks. Automotive electronics became popular in the 1960s with the...[Details]
In recent years, the development of automotive batteries has become a focus of attention. Compared with other rechargeable batteries, lithium-ion batteries have the advantages of high specific ene...[Details]
Any power transmission and distribution equipment and power-consuming devices cannot be pure resistive loads, so they must occupy a certain amount of reactive power. The existence of reactive curre...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
