synchronous static RAM designed to provide a burstable,
high-performance memory for high speed networking and
communication applications. It is organized as 262,144
words by 16 bits and 18 bits, fabricated with
ISSI
's
advanced CMOS technology. The device integrates a 2-bit
burst counter, high-speed SRAM core, and high-drive
capability outputs into a single monolithic circuit. All
synchronous inputs pass through registers controlled by
a positive-edge-triggered single clock input.
Write cycles are internally self-timed and are initiated by
the rising edge of the clock input. Write cycles can be from
one to four bytes wide as controlled by the write control
inputs.
Separate byte enables allow individual bytes to be written.
BW1
controls DQ1-8,
BW2
controls DQ9-16, conditioned
by
BWE
being LOW. A LOW on
GW
input would cause all
bytes to be written.
Bursts can be initiated with either
ADSP
(Address Status
Processor) or
ADSC
(Address Status Cache Controller)
input pins. Subsequent burst addresses can be generated
internally and controlled by the
ADV
(burst address
advance) input pin.
The mode pin is used to select the burst sequence order,
Linear burst is achieved when this pin is tied LOW.
Interleave burst is achieved when this pin is tied HIGH or
left floating.
FAST ACCESS TIME
Symbol
t
KQ
t
KC
Parameter
Clock Access Time
Cycle Time
Frequency
-166
3.5
6
166
-150
3.8
6.7
150
-133
4
7.5
133
-5
5
10
100
Units
ns
ns
MHz
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any
[align=left][color=#000][size=4]Hello everyone; [/size][/color][/align][align=left][color=#000][size=4] The program's log definitions are all background files, why can't they be refreshed in real time...
[align=left][font=微软雅黑]Introduction[/font][/align][align=left][font=微软雅黑]Zero-drift amplifiers use a unique self-correcting technique to provide ultra-low input offset voltage (Vos) and near-zero inpu...
The circuit diagram is shown below, L1 and L2 are inductors. The input waveform at point A is a DC level of about 45V, and the input waveform at point B is shown in the figure below. The shaded part i...
I have always wanted to connect to a database on a PC, such as SQL Server, MySQL, etc., through a program on Windows CE, but I have not been able to do it. I wonder if there are any experts who can gi...
One day I was chatting with a friend, who is a technical director of a large domestic Internet company. My friend summarized the hard work he had accumulated in nearly ten years of R&D work into two p...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
Every time I go home and walk up the stairs, I am always scared. The corridor lights are often broken, and no one changes the bulbs, or they are not smart enough and need to be operated manually. E...[Details]
The capacity of a battery depends on the amount of charge and discharge, in addition to some factors of the battery itself. Obviously, if the charge and discharge of the battery can be recorded all...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
As a new type of centralized and decentralized elevator control system, serial communication has been widely used in China. Compared with the previous centralized and unified control system, each s...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
