EEWORLDEEWORLDEEWORLD

Part Number

Search

GUS-TSCB-02-1262-DB

Description
Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 12600ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 3117,
CategoryPassive components    The resistor   
File Size530KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUS-TSCB-02-1262-DB Overview

Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 12600ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 3117,

GUS-TSCB-02-1262-DB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid802324158
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL5.18
structureChip
JESD-609 codee0
Network TypeBussed
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.9 mm
Package length7.8 mm
Package formSMT
Package width4.4 mm
Rated power dissipation(P)0.05 W
resistance12600 Ω
Resistor typeARRAY/NETWORK RESISTOR
size code3117
technologyTANTALUM NITRIDE/NICKEL CHROME
Temperature Coefficient50 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Tolerance0.5%
Operating Voltage100 V
Resistors
Make Possible
Surface Mount TSSOP
Surface Mount TSSOP
Resistor Networks
Resistor Networks
TSSOP Series
Absolute tolerances to ±0.1%
Tight TC Tracking to ±5ppm/°C
TSSOP Series
Ratio match tolerances to ±0.05%
Absolute tolerances to ±0.1%
Ultra-stable tantalum nitride resistors
Tight TC Tracking to ±5ppm/°C
Standard Sn/Pb and Pb-free terminations available
Ratio match tolerances to ±0.05%
Ultra-stable tantalum nitride resistors
Standard Sn/Pb and Pb-free terminations available
All Pb-free parts comply with EU Directive 2011/65/EU (RoHS2)
IRC’s TaNSil
®
TSSOP resistor networks are ideally suited for high volume applications that demand a small, low-profile footprint.
The small wire-bondable chip package provides higher component density, lower resistor cost and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking, low cost and miniature package.
Excellent performance in harsh, humid environments is a trademark of IRC’s self-passivating TaNSil
®
resistor film.
For applications requiring high performance resistor networks in a low cost, low profile, surface mount package, specify IRC TSSOP
resistor networks.
Electrical Data
Resistance Range
Absolute Tolerance
Ratio Tolerance to R1
Absolute TCR
Tracking TCR
Element Power Rating @ 70°C
Isolated Schematic
Bussed Schematic
Package Power Rating @ 70°C
Rated Operating Voltage
______
(not to exceed
P x R)
Operating Temperature
Noise
100mW
50mW
16-Pin
20-Pin
24-Pin
800mW
1.0W
1.0W
10Ω to 250KΩ
To ±0.1%
To ±0.05%
To ±25ppm/°C
To ±5ppm/°C
Environmental Data
Test Per
MIL-PRF-83401
Typical
Delta R
Max Delta
R
Thermal Shock
±0.02%
±0.1%
Power Conditioning
±0.03%
±0.1%
High Temperature Exposure
±0.03%
±0.5%
Short-time Overload
±0.02%
±0.5%
100 Volts
-55°C to
+125°C
<-30dB
Low Temperature Storage
±0.03%
±0.5%
Life
±0.05%
±0.1%
General Note
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s
right to make
considered accurate at time of going to print.
TT Electronics reserves the
own data and is
changes in product specification without notice or liability.
All information is subject to TT Electronics’
South Staples Street • Corpus Christi Texas
at time of
© IRC Advanced Film Division
• 4222
own data and is considered accurate
78411 USA
going to print.
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
TSSOP Series Issue January 2009 Sheet 1 of 4
www.ttelectronicsresistors.com
© TT Electronics plc
07.14
Should GND be routed last? If a copper-clad design is required, does GND need to be routed?
I remember seeing in a post that if the board is copper-clad, there is no need to lay GND, it will be automatically covered. Is this true? Or did I read it wrong?...
44444444444444 PCB Design
Robot car sensor design task first phase
Simple open source car robot sensor design(This design is the first step in the open source robot development roadmap, and there is almost no technical difficulty. It is only to coordinate the divisio...
artruth Robotics Development
STM32NANDFLASH timing problem
The official ST data sheet provides the formulas for calculating the various timing parameters of FSMC. The following formula seems to be incorrect. I hope experts can give me some advice. Thank you v...
自然的天意 stm32/stm8
About 2812 external SPI memory 25fl064
I've been trying to adjust the 2812 external SPI memory 25fl064, but it doesn't work. It's urgent. I beg you, I really beg you to help me, a rookie! I just want to read the memory ID, but it doesn't w...
lwangliu DSP and ARM Processors
I just thought of a way to deal with people posting a lot of ads on the forum at once.
I often see newly registered users posting a lot of illegal ads at once. I wonder how they deal with it now? I see some forums restricting new users from posting. For example, new users have to go thr...
wangfuchong Suggestions & Announcements
Let your software fly!
I hope everyone can share their experiences in their spare time, so that we can grow faster....
小瑞 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2295  2252  350  2759  41  47  46  8  56  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号