Data and signal line chokes
Common-mode chokes, ring core
4.7 … 68 mH, 200 … 700 mA, 40 °C
Series/Type:
B82720H15
October 2008
7f
fÁRspp
Date:
©
EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
Data and signal line chokes
Common-mode chokes, ring core
Rated voltage 42 V AC/80 V DC
Rated inductance 4.7 mH to 68 mH
Rated current 200 mA to 700 mA
Construction
■
■
■
■
B82720H15
Current-compensated ring core double choke
Ferrite core
Polycarbonate case (UL 94 V-0)
Polyurethane potting (UL 94 V-0)
Features
■
Suitable for automatic insertion
■
Suitable for wave soldering
■
RoHS-compatible
Applications
■
Telecom switching systems
■
Terminal systems
■
Measuring and control lines
Terminals
■
■
■
■
Base material CuNi18Zn20
Layer composition Ni, Sn
Hot-dipped
Lead spacing 10
×
7.5 (mm)
Marking
Manufacturer, ordering code, rated inductance,
rated current, date of manufacture (YYWWD)
Delivery mode
Cardboard box
Please read
Cautions and warnings
and
Important notes
at the end of this document.
2
10/08
Data and signal line chokes
Common-mode chokes, ring core
Dimensional drawing and pin configuration
13±0.3
10±0.2
1
2
B82720H15
7.5±0.2
9.5
_
0.4
1
2
4
3
4
7.6
_
0.3
3
3.5
_
0.5 14±0.3
1.5
5±0.2
Tolerances to ISO 2768-M
unless otherwise noted.
IND0212-V
0.5
Dimensions in mm
Technical data and measuring conditions
Rated voltage V
R
Rated temperature T
R
Rated current I
R
Rated inductance L
R
Inductance tolerance
Inductance decrease
ΔL/L
0
Stray inductance L
stray,typ
DC resistance R
typ
Solderability (lead-free)
42 V AC (50/60 Hz) / 80 V DC
40 °C
Referred to 50 Hz and rated temperature
Measured with Agilent 4284A at 10 kHz, 0.1 mA, 20 °C
Inductance is specified per winding.
–30%/+50% at 20 °C
< 10% at DC magnetic bias with I
R
, 20 °C
Measured with Agilent 4284A at 10 kHz, 5 mA, 20 °C,
typical values
Measured at 20
°C,
typical values, specified per winding
Sn96.5Ag3.0Cu0.5: (245
±5)
°C, (3
±0.3)
s
Wetting of soldering area
≥
95%
(to IEC 60068-2-20, test Ta)
(260
±5)
°C, (10
±1)
s
(to IEC 60068-2-20, test Tb)
40/125/56 (to IEC 60068-1)
–25 °C … +40 °C,
≤
75% RH
Approx. 2.1 g
Resistance to soldering heat
(wave soldering)
Climatic category
Storage conditions (packaged)
Weight
Please read
Cautions and warnings
and
Important notes
at the end of this document.
3
10/08
Data and signal line chokes
Common-mode chokes, ring core
Characteristics and ordering codes
L
R
mH
4.7
10
28
47
68
L
stray,typ
nH
300
400
700
1000
1200
I
R1)
mA
700
600
400
300
200
R
typ
mΩ
500
700
1200
2700
3300
V
test
V DC, 2 s
750
750
750
750
750
Ordering code
B82720H15
B82720H0015A016
B82720H0015A025
B82720H0015A028
B82720H0015A030
B82720H0015A035
Impedance |Z| versus frequency f
measured with windings in parallel at 20 °C,
typical values
10
6
Ω
B82720
| Z|
10
5
IND0213-6
Current derating I
op
/I
R
versus ambient temperature
IND0682-K-E
1.4
I
op
I
R
1.2
1.0
10
4
T
R
= 40
˚
C
0.8
10
3
10
2
H0015A035
H0015A030
H0015A028
H0015A025
H0015A016
0.6
0.4
0.2
10
1 4
10
10
5
10
6
Hz 10
f
7
0
0
20
40
60
80 100
˚
C
140
T
A
1) Types with higher rated current on request.
Please read
Cautions and warnings
and
Important notes
at the end of this document.
4
10/08
Cautions and warnings
■
Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■
If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
■
The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■
Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■
Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read
Cautions and warnings
and
Important notes
at the end of this document.
5
10/08
京公网安备 11010802033920号
EEWORLD
