EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001KG-105LCDI

Description
IC osc clock QD freq 10clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Download Datasheet Parametric View All

8N4Q001KG-105LCDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001KG-105LCDI - - View Buy Now

8N4Q001KG-105LCDI Overview

IC osc clock QD freq 10clcc

8N4Q001KG-105LCDI Parametric

Parameter NameAttribute value
Datasheets
IDT8N4Q001 Rev G
FemtoClock®
NG Ordering Guide
Standard Package364
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTray
TypeClock Oscill
Cou-
Frequency100MHz, 125MHz, 150MHz, 156.25MHz
Voltage - Supply3.135 V ~ 3.465 V
Current - Supply160mA
Operating Temperature-40°C ~ 85°C
Package / Case10-CLCC
Supplier Device Package10-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N4Q001KG-105LCDIIDT8N4Q001KG-105LCDI-ND
Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
Learn how to use an oscilloscope as a recorder
A waveform recorder can collect signals for a long time and save the data to the hard disk of the device. The length of the collection time depends on the sampling rate and the hard disk capacity. How...
Micsig麦科信 Integrated technical exchanges
I use the GPRS module to dial up to the Internet, but the local IP address is the same as the remote IP address, and the data is not sent to the specified server port. What should I do?
I use the GPRS module to dial ATD*99# to access the Internet. I use the serial port to output information to check the status: local IP address:10.145.168.65 remote IP address:10.145.168.65 tcpip_open...
njzgw Embedded System
[Xingkong Board Python Programming Learning Main Control Board] 2: Burning System Image
On the Xingkong board tutorial page, the official gave the firmware Baidu network disk address: https://pan.baidu.com/s/1KXWOm8HC575mAiCWB434Pw (extraction code: unih), and I saw that the version is v...
数码小叶 Embedded System
How does 6045 generate pwm waves
How to use pwm wave to adjust the backlight on the 6045 development board launched by Shenzhen Tianmo Technology Company? I made corresponding modifications to the board-sam9m10g45ek.c file in the ker...
yjh19891026 FPGA/CPLD
Rewrite the LM3S clock configuration function to a dedicated initialization function
Yesterday I talked about my understanding of the LM3S clock configuration function. Today I made some modifications to the clock part of the graphical configuration file I made two days ago. Because t...
柳叶舟 Microcontroller MCU
Does anyone have a demo of using WINCE to directly operate the IIC controller?
Give me a DEMO to see, thanks sasinop@hotmail.com...
didi111 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1895  1432  653  2856  671  39  29  14  58  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号