EEWORLDEEWORLDEEWORLD

Part Number

Search

M39003/040364B

Description
Tantalum Capacitor, Tantalum (dry/solid),
CategoryPassive components    capacitor   
File Size778KB,15 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Download Datasheet Parametric View All

M39003/040364B Overview

Tantalum Capacitor, Tantalum (dry/solid),

M39003/040364B Parametric

Parameter NameAttribute value
Objectid7074111146
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL7.5
capacitance0.6 µF
Capacitor typeTANTALUM CAPACITOR
diameter5.26 mm
dielectric materialsTANTALUM (DRY/SOLID)
JESD-609 codee0
leakage current0.0005 mA
length24.26 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formAxial
method of packingBulk
polarityNON-POLARIZED
positive tolerance10%
Rated (DC) voltage (URdc)100 V
GuidelineMIL-PRF-39003
surface mountNO
Delta tangent0.03
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeWIRE
Tantalum Through-Hole Capacitors – Hermetically Sealed
T111 Axial MIL–PRF–39003 Non-Polar and
T213 (CSR91 Style)
Overview
The T111/T213 Series is primarily designed for use in tuned
low frequency circuits, phasing low voltage AC motors,
servo systems and other applications where reversal of
polarity is a primary consideration. The T111 unit consists
of two polar T110 Series hermetically sealed tantalum
capacitors, electrically and mechanically connected back-
to-back and supported by an outer corrosion-resistant
metal sleeve. They exhibit comparable electrical and
performance characteristics of T110 Series. Available in
capacitance values from 0.0023 µF to 160 µF in ±20% and
±10% tolerances, the T111 series is offered in working
voltages of 6 VDC to 100 VDC at +85°C.
Benefits
• Taped and reeled per EIA Specification RS–296
• Marking per MIL–STD–1285
• Qualified to MIL–PRF–39003 (CSR91 Style)
• Failure rate options: Graded – B, C, D, and G
Exponential – M, P, R, and S*
• Capacitance values of 0.0023 μF to 160 μF
• Tolerances of ±5%, ±10% and ±20%
• Voltage rating of 6 – 100 VDC
• Operating temperature range of −55°C to +125°C
• Case sizes: A, B, C, D
*Failure rates apply to military products only
Applications
Typical applications include use in tuned low frequency circuits, phasing low voltage AC motors, servo systems and other
applications where reversal of polarity is a primary consideration.
Built Into Tomorrow
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2032_T111_AXIAL_T213 • 7/2/2021
1
Description of MSP430FR5739 Experimental Board Development Tool
Everyone has received the MSP430FR5739 experimental board, and many forum friends have reported that the IDE they are using does not support the MSP430FR5739 chip.Especially those forum friends who us...
wstt Microcontroller MCU
I would like to ask you, which brand of gateway supporting Zigbee HA profile is better now?
I want to get a zigbee host that can be connected to an iPhone or iPad via wifi or rj45 for control. I don't know which brand is good....
nicolas_wang RF/Wirelessly
How to determine the number of board layers
Does the PCB diagram determine the number of layers by looking at the number of layers between the top and bottom layers? How can we determine the number of layers if we only have the physical object?...
大发明家 PCB Design
Analog/digital mixed circuit accelerated simulation technology (I)
Analog/digital mixed circuit accelerated simulation technology (I)[Source: Electronic Engineering Journal] [Author: Lu Zhenting, Song Lei] [Time: 2006-1-17 8:58:49] [Clicks: 80]Nowadays, SoC designs i...
fighting Analog electronics
Several circuit designs that must be understood by microcontrollers
1. Selection of pull-up resistor for MCU  You can see that when the resistor R1=10k in the reset circuit, RST is high level, and when R1=50, RST is low level. It is obvious that when R1=10k, it is wro...
Jacktang Microcontroller MCU
Let's take a look at the STM32 serial port program. I don't know where the error is. I hope the experts can give me some advice.
1, USART_ReceiveData(USART1)); } } } } //void RCC_config(void) Function name: RCC_config(void) Function function: to initialize the system clock Entry parameter: none Exit parameter: none Time: 11.12....
OnlyCxue Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1130  1240  77  96  653  23  25  2  14  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号