14. Table of Figures ______________________________________________________________________ 24
Information in this document is provided solely to enable the use of Future Designs products. FDI assumes no liability whatsoever, including infringement of any
patent or copyright. FDI reserves the right to make changes to these specifications at any time, without notice. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Future Designs, Inc. 2702 Triana Blvd,
Huntsville, AL 35805
NOTE: The inclusion of vendor software products in this kit does not imply an endorsement of the product by Future Designs, Inc.
2011 Future Designs, Inc. All rights reserved.
®
uEZ
is a registered trademark of Future Designs, Inc.
Microsoft, MS‐DOS, Windows, Windows XP, Microsoft Word are registered trademarks of Microsoft Corporation.
Other brand names are trademarks or registered trademarks of their respective owners.
FDI PN: MA00026
Revision: 1, 10/14/2011 3:02:00 PM
Printed in the United States of America
iii
1. Introduction
The DK‐TS‐KIT is optimized to save development time in typical embedded control applications. Its modular format uses
a base carrier board, a core CPU DIMM board and an LCD carrier board. The base carrier board includes expansion
connectors for added flexibility and a range of configurations.
This manual supports the following DK‐TS‐KIT part numbers:
DK‐43WQT‐RX62N 4.3” WQVGA Touch Screen LCD Kit for the RX62N, Tianma PN: TM043NBH02
DK‐47WQT‐RX62N 4.7” WQVGA Touch Screen LCD Kit for the RX62N, Tianma PN: TM047NBH01
2. Functional Description
CARRIER
200 pin SO‐DIMM Socket
RS232 Serial Port (Male DB9)
CAN Port (Male DB9) – alternate with RS485
RS485 Full Duplex (Male DB9) – alternate with CAN
10/100 Ethernet Connector
Optional 802.11 b/g WiFi Module
USB Type‐A Host Connector
USB Mini‐B Device Connector
LM75 Temperature Sensor
3‐axis Accelerometer
Real‐time Clock with Super‐Cap Backup
Four User Pushbuttons
Four User LEDs
Speaker
External I2C Connector (Optional)
Reset Button
LCDCARRIER
4.3” Active TFT WQVGA LCD (480x272) mounted to LCDCARRIER 4WQ Board or
4.7” Active TFT WQVGA LCD (480x272) mounted to LCDCARRIER 4WQ Board
Touch Screen
LED Backlight
1
3. ESD Warning
The DK‐TS‐KIT is shipped in a protective anti‐static package. The Kit must not be subjected to high electrostatic
potentials. Damage may occur to the Kit that will not be covered under warranty. General practice for working with
static sensitive devices should be followed when working with the DK‐TS‐KIT.
4. Requirements
The DK‐TS‐KIT comes with all necessary cables to begin development right away. The Kit includes a Type‐A to Mini‐B
USB cable, a CAT5 Ethernet cable, a 5.0VDC, 2A, AC Wall Adapter and either the Segger JTAG Debugger. A PC will be
required to install the development tools to program the SOMDIMMs. The DK‐TS‐KIT will be powered using the 5VDC AC
Wall Adapter included in the kit and may be plugged into any standard 110VAC wall socket. An available Ethernet
network will be needed for using the Ethernet connection on the CARRIER and a free USB port will be needed for using
the available USB connections.
CAUTION: DO NOT POWER THE DK‐TS‐KIT WITH ANY OTHER POWER THAN 5VDC. USE OF ANY OTHER ADAPTER MAY