Series - Fundamental Quartz Crystal, 3.579545MHz Nom, HC/49US, 2 PIN
ABL2-3.579545MHZ-S-4X-L2-T Parametric
Parameter Name
Attribute value
Is it lead-free?
Lead free
Is it Rohs certified?
conform to
Objectid
1323127318
package instruction
HC/49US, 2 PIN
Reach Compliance Code
compliant
Country Of Origin
Mainland China
YTEOL
6.22
Other features
AT-CUT; TR
Ageing
5 PPM/YEAR
Crystal/Resonator Type
SERIES - FUNDAMENTAL
Drive level
100 µW
frequency stability
0.002%
frequency tolerance
30 ppm
Installation features
THROUGH HOLE MOUNT
Nominal operating frequency
3.579545 MHz
Maximum operating temperature
70 °C
Minimum operating temperature
physical size
L11.5XB5.0XH2.5 (mm)/L0.453XB0.197XH0.098 (inch)
Series resistance
180 Ω
surface mount
NO
ABL2-3.579545MHZ-S-4X-L2-T Preview
HC/49US (AT49) MICROPROCESSOR CRYSTAL
ABL2 Series
Moisture Sensitivity Level (MSL) – This product is Hermetically Sealed
and not Moisture Sensitive - MSL = N/A: Not Applicable
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
FEATURES:
• Reduced height at 2.5mm
• High reliability & Low Cost
• Tight stability & extended temperature
• Proven resistance welded metal package
STANDARD SPECIFICATIONS:
Parameters
Frequency Range
Minimum
3.579545
3.579545
Operation mode
24.01
24.01
Operating Temperature
Storage Temperature
Frequency Tolerance
Frequency Stability over the Operating
Temperature
(
ref. to +25°C)
Equivalent series resistance
(R1)
Shunt capacitance
(C0)
Load capacitance
(CL)
Drive Level
Aging @
25°C per year
Insulation
Resistance
Drive Level Dependency
(DLD,
Minimum
7 points tested:
from
1µW to
500µW)
0
-55
-50
-50
APPLICATIONS:
• Home electronics
• Computers, modems, and communications
• Automotive and industrial
• High-precision TCXO and clock applications
• Microprocessors
Typical
Maximum
70
24.0
70.00
50.00
+70
+125
+50
+50
See table 1 below
7
18
100
500
±10
25% of
Max
ESR
Max
ESR in
Table 1
1000
±5
ºC
ºC
ppm
ppm
Ω
pF
pF
µW
ppm
MΩ
ppm
Ω
Ω
MHz
Fundamental
AT-
cut
(Standard)
3
rd
OT
AT-cut
(Standard)
Fundamental
AT-
cut or
BT-cut (See
options)
See options
See options
See options
Units
Notes
See options
@
100Vdc
±
15V
Δfrequency
(Max –
Min)
ΔESR
(Max – Min)
Max
ESR over DLD
range
Table 1
Frequency (MHz)
3.579 - 4.999 (Fund.)
5.000
-
5.999
(Fund.)
6.000 -
7.999
(Fund.)
8.000
-
8.999
(Fund.)
9.000
-
9.999
(Fund.)
10.000
-
15.999
(Fund.)
16.000
-
50.000
(Fund.)
24.01
-
31.999
(3rd
O/T)
32.000 -
70.00
(3rd
O/T)
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
ESR(Ω) max.
180
120
100
80
60
50
40
100
80
Revised: 01.08.13
30332
Esperanza, Rancho Santa
Margarita,
California 92688
tel 949-546-8000
|
fax
949-546-8001
|
www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
HC/49US (AT49) MICROPROCESSOR CRYSTAL
ABL2 Series
OPTIONS AND PART IDENTIFICATION:
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
ABL2 -
Frequency in MHz
Please specify the frequency
in xx.xxxxMHz.
e.g. 14.3181MHz
Load Capacitance (pF)
Please specify CL
(Minimum 10pF) in pF or
S for series
Custom ESR if other
than standard
R□
□:
Specify a value in
Ω
(e.g.: R40)
MHz-
-
-
-
-
-
Packaging
Blank: Bulk
T: Tape & Reel
TRAY: Tray
Value Added
I
Insulator Tab
L2
Middle 3rd lead
QXX
Trimmed leads
Q15
for 0.15" length
Oscillation Mode
F: Fund. AT>24MHz
FB: Fund. BT>24MHz
Operating Temp.
A: -10°C ~ +60°C
B: -20°C ~ +70°C
C: -30°C ~ +70°C
N: -30°C ~ +85°C
D: -40°C ~ +85°C
J*: -40°C ~ +105°C
K*: -40°C ~ +125°C
L*: -55°C ~ +125°C
Freq. Tolerance
H5: ± 5 ppm
1: ± 10 ppm
7: ± 15 ppm
2: ± 20 ppm
3: ± 25 ppm
4: ± 30 ppm
Freq. Stability
U**: ± 10 ppm
G: ± 15 ppm
X: ± 20 ppm
W: ± 25 ppm
Y: ± 30 ppm
H: ± 35 ppm
Q: ± 100 ppm
R: ± 150 ppm
NOTE:
* Frequency stability ±50ppm, ±100ppm, ±150ppm only. Contact ABRACON for tighter frequency stability.
** -10 to +60C only.
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
Revised: 01.08.13
30332 Esperanza, Rancho Santa Margarita, California 92688
tel 949-546-8000
|
fax 949-546-8001
| www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
HC/49US (AT49) MICROPROCESSOR CRYSTAL
ABL2 Series
OUTLINE DIMENSIONS:
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
ABL2 SERIES HC49/US (AT49)
MICROPROCESSOR CRYSTAL
Date of Issue: Jan. 2
nd
, 2013
Page (8) of (10)
8.0
Packaging:
L
5.5mm Min
20.0 ± 0.5mm
Packaging
Bulk
Tape & Reel
11.5 x 5.0 x 2.5 mm
Abracon Drawing # 450715
Revision #: K
T= Tape and reel (1,000pcs/reel)
Dimensions: inch (mm)
TAPE & REEL:
T= Tape and reel (1,000pcs/reel)
Dimensions: mm
ATTENTION:
Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applica-
tions. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where
component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and
authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information.
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
Revised: 01.08.13
30332 Esperanza, Rancho Santa Margarita, California 92688
tel 949-546-8000
|
fax 949-546-8001
| www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
Zero-based MCU video tutorial - Lecture 01 Building C51 integrated development environment This lecture first builds a 51 MCU hardware and software development system, and demonstrates the process of ...
As shown in the figure, for such a circuit, the voltage at the WAKE point is about 20V without a voltage regulator. Will the voltage at the WAKE point be 18V after adding a voltage regulator?...
Edge detection is to detect the jump of input signal or FPGA internal logic signal, that is, the detection of rising or falling edge of the signal. To learn edge detection circuit, we should first lea...
A chip, in which two pins are two signals A and B that are easily interfered with. They are connected to the outside. Assume that the chip is on the front. In the first case, both extend to the right,...
Question: Can I create multiple device objects in a driver, and do the IRPs sent to different device objects share the same dispatch routine? Background of the question: I want to write a filter drive...
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
1. Function prototype In the function library officially provided by STM32, you can find functions like HAL_Delay(). This function uses a timer to achieve a more accurate time delay and provides it...[Details]
The update interrupt initialization configuration of the stm32 advanced timer TIM1 is not much different from that of the ordinary timer. What needs to be paid attention to is the configuration of TI...[Details]
Recently, the " ZTE
incident"
caused by the Sino-US trade war
has caused heated discussions in the electronics industry. It not only reflects that Chinese companies are lagging behind in the...[Details]
In Windows environment, the source code is encoded in UTF-8. If the source file created by STM32CubeMX contains Chinese comments, then using STM32CubeMX to regenerate the source code will cause the C...[Details]
1. The first project We are going to create the first project, which is mainly for project analysis, so that we can understand how CubeMX works and how to trace the code logic. Okay, no more nonsense...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
After we understand the use of libopencm3, we find that libopencm3 is only suitable for small projects. Its biggest feature is the convenience of USB. So when we configure large projects, is there a ...[Details]
background After the hardware engineer completed the PCB and schematic design, the routine was modified according to the tutorial of Zhengdian Atom to verify the correctness of the hardware. STM32F...[Details]
The goal of this article is to build a TCP client based on the previous project that can ping the PC, and can actively send data to the PC, and can also send and receive data with the PC, and display...[Details]
The last two blogs talked about a version problem of STM32CubeMX and the problem of hardware reset. When you solve these two problems, you will find that after the program is burned into the board, t...[Details]
Automotive LCD Instrument Clock EMI Solution As early as 2014, the market size of China's automotive full LCD instrument has reached 3.506 billion yuan, and it is expected that by 2020, this s...[Details]
The Wassenaar Arrangement, everything started during the Cold War. Let's learn more about it with the embedded editor.
background
After the end of World War II, the United States ...[Details]
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
