L143S514AP datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> L143S514AP

L143S514AP: DescriptionArray/Network Resistor, Isolated, Metal Glaze/thick Film, 0.2W, 510000ohm, 100V, 2% +/-Tol, -100,100ppm/Cel,; CategoryPassive components The resistor; File Size61KB，5 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

L143S514AP Overview

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.2W, 510000ohm, 100V, 2% +/-Tol, -100,100ppm/Cel,

L143S514AP Parametric

Parameter Name	Attribute value
Objectid	913398496
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Conformal Coated
Lead length	3.556 mm
lead spacing	2.54 mm
Network Type	Isolated
Number of terminals	14
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	4.95 mm
Package length	35.56 mm
Package form	SIP
Package width	2.41 mm
method of packing	Ammo Pack
Rated power dissipation(P)	0.2 W
resistance	510000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	L(ISOLATED,2%)
technology	METAL GLAZE/THICK FILM
Temperature Coefficient	100 ppm/°C
Tolerance	2%
Operating Voltage	100 V

Preview

Download Datasheet

View All

MODEL L SERIES

Thick Film

Low Proﬁle SIP

Conformal Coated

Resistor Networks

RoHS Compliant

ELECTRICAL

Standard Resistance Range, Ohms

Standard Resistance Tolerance, at 25°C

Operating Temperature Range

Temperature Coefﬁcient of Resistance

Temperature Coefﬁcient of Resistance, Tracking

Maximum Operating Voltage

Insulation Resistance

ENVIRONMENTAL

22 to 1Meg

±2%

Optional: ±1% (F Tol.), ±5% (J Tol.)

-55°C to +125°C

±100ppm/°C (<100 Ohms = ±250ppm/°C)

±50ppm/°C

100Vdc or

√PR

≥10,000

Megohms

Thermal Shock plus Power Conditioning

Short Time Overload

Terminal Strength

Moisture Resistance

Mechanical Shock

Vibration

Low Temperature Storage

High Temperature Exposure

Load Life, 1,000 Hours

Resistance to Solder Heat (Per MIL-STD-202, Method 210, Cond.B)

Dielectric Withstanding Voltage

Marking Permanency

Lead Solderability

Flammability

Storage Temperature Range

Speciﬁcations subject to change without notice.

∆R

0.70%

∆R

0.25%

∆R

0.25%

∆R

0.50%

∆R

0.25%

∆R

0.25%

∆R

0.25%

∆R

0.50%

∆R

1.00%

∆R

0.25%

200V for 1 minute

MIL-STD 202, Method 215

MIL-STD 202, Method 208

UL-94V-O Rated

-55°C to +150°C

4-47

Model L Series

Recommended Resources

phase shift oscillator

TA7688P power amplifier circuit diagram

Incandescent lamp life extension electronic controller (2)

Proximity switch circuit diagram of tca205a

LED flasher

Low noise field effect transistor crystal oscillator

[More pictures] Real shot: The test site of Feiling embedded S3C2440 and S3C6410 development boards: Today, I went to Feiling with an engineer to discuss ODM cooperation. I bought their 2440 development board before. At that time, I just saw that their promotion said "the development board is suitabl...; lina_90 Embedded System

Inline strings in AVR programs: [i=s]This post was last edited by shipeng on 2017-12-28 16:27[/i] Since the RAM and ROM of AVR microcontrollers use non-linear addressing, the address mapping overlaps, which brings us a lot of troubl...; shipeng Microchip MCU

ADSP-BF561 DMA Mode Introduction: 9 Direct Memory Access 9 [font=宋体]Direct Memory Access (DMA) [/font] The processor uses Direct Memory Access (DMA) to transfer data within memory spaces or between a memory space and a peripheral. The...; feelang DSP and ARM Processors

What changes will occur if RFID technology is applied to clothing production?: With the rapid development of Internet of Things technology, radio frequency identification technology (RFID) has achieved great success in the production process of various fields. RFID technology is...; Jacktang RF/Wirelessly

[Transfer] Several sketches teach you to distinguish between digital ground, analog ground, power ground, and single-point grounding: When we are wiring PCBs, we always face the situation that there are two or three kinds of ground on a board. The fool-proof way is to cover the whole board with copper as long as it is ground. This i...; eric_wang Integrated technical exchanges

How to directly access the L2CAP layer of the Bluetooth stack under ce?: Only a simulated serial port link can be established through socket. I hope to directly obtain the data of the l2cap layer and send and receive Bluetooth data at the l2cap layer. According to the docu...; zhp3245 Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components